Showing posts with label golf jetta. Show all posts
Showing posts with label golf jetta. Show all posts

Monday, May 3, 2010

1992-2003 Volkswagen Golf, Jetta, GTI, Cabrio Heating Air Conditioning 87 - A/C controls and mechanical components, servicing

Installing and checking expansion valve insulator
1. Insulator
2. Expansion valve
Insulation is used around expansion valve to prevent moisture (condensation) build-up and to protect expansion valve from high engine compartment temperatures and the resulting decrease in A/C system cooling performance.
Install insulator - 1 - over expansion valve - 2 - (arrow).
Check insulator for damage and proper fit, and replace if necessary.

Removing and installing evaporator water drain valve
1. Water drain valve
2. Bulkhead
3. Water drain tube (on evaporator housing)
4. Mounting recess
To remove, carefully pull water drain valve - 1 - from drain tube - 3 - .
Install water drain valve so that valve flap opens from bottom.
Make sure valve flap is free of dirt, wax or undercoating; clean if necessary.

Download

Sunday, May 2, 2010

VW Jetta, Golf, New Beetle 1.9L TDi Unichip PnP Installation Instructions

Although the PnP kits and ECU’s are identical, the New Beetle’s EC’s location is different than the Jetta/Golf; therefore these instructions are split – the first section describes Golf/Jetta installation and the second section describes Beetle installation.
(2) The ECU connectors lock and unlock by pulling the “T-handle” located at the connector’s edge. Look at the locking handles on the PnP harness and familiarize yourself with the mechanism before trying to remove the OEM plugs.
(3) When trying to remove the OEM Plugs from the ECU, getting your fingers into the T-handles can be difficult. You can gently pry the T-handles back using a screw driver.
(4) The Golf/Jetta OEM ECU bracket will not reinstall with the Unichip PnP harness in place without modification. You can easily modify your bracket as outlined below or can by a modified bracket from UNA (UNA Part # 9950001).

Installation Procedures - Golf/Jetta
1. Using the 10mm wrench, disconnect the car’s battery at the negative terminal in the engine compartment behind the driver’s side headlight.
2. (Photo 1) Remove the Windshield Wiper Arms
Note: Installing the wiper arms in the incorrect position may result in damage when they are actuated.
a. Using the pick, pry off the windshield wiper drive spindle covers.
b. Record the arm position on the drive spindle with a marking pen to assist correct reinstallation.
c. Using the 13mm socket, remove the nut securing each wiper arm blade, and remove the arms.
3. (Photo 2) Remove the plastic Rain Tray Cover
a. Remove the rubber seal along the top of the firewall
b. Slip your fingers between the windshield and the tray at the mid-span point and gently work towards one side unplugging the securing tabs. DO NOT USE ANY TOOLS as they may damage the tray, tray tabs, or windshield. Repeat towards the opposite side and remove the tray.
c. Remove the cover; the cover extends underneath the cowl on the passanger’s side. Remove it by pulling it forward into the engine compartment.

Download

Saturday, May 1, 2010

MKIII 2.0 Golf/Jetta Rear Disk Brake DIY

This "how to" assumes you have some basic tools, and safety gear. Safety glasses should be worn at all times when working with tools and automotive fluids. Always use a hydraulic jack and safety stands when lifting or getting under a vehicle. If you are unsure on where to safety lift your vehicle, refer to its owners guide. Brake dust can contain asbestos which has been found to cause cancer. The writer of this how to assumes zero liability in how to use this guide, or any damages that may come from it to you, your property, or others and others property. If you are uncertain at any point, refer to a qualified automotive technician.

Basic Rules, clean brake fluid up with cold water. Keep all fluids, water, dirt, and oil out of the brake system (except for clean brake fluid). Keep all and any grease off pads, shoes, and rotor brake surfaces. If pads become contaminated with grease or oil, throw them out and buy new ones. If rotors become oily, clean them with brake clean, or hot soapy water.

Why Do This?:
Pretty easy, you need rear brakes. This DIY will help you take them apart, clean, and install new pads, rotors, and bearings. For the most part the same rules and tools apply as a front brake job.
However, it is absolutely necessary to have a seal driver set, and a disk brake real caliper retractor tool.
I strongly suggest that if you have never done a brake job, do the fronts fist. Or at least read up on that DIY.
Before you do this make sure the parking brake works 100% if it does
NOT your calipers may be frozen (stuck) and this job is hard and pointless!!!
If you have never installed brakes, or bearings read up on these sites first.
Bearing End Play Adjustment
Basic Bearing Replacement
Installing New Bearing Races into a Rotor
Greasing The Bearings

Download