Now when you have removed the screws you need to push the light in the blue arrow direction opposite direction on the other headlight so you can pull out a ball head screw out of its holder If it doesn t go out easy take a look where the yellow arrow points in the corner of the wing and you will see the ball head screw
Spray it with a bit of WD40 or some silicone spray so it can come out easily Now push hit the head light out of it After you have done that disconnect all connectors that are attached to the headlight Now take the headlight off Here is the procedure shown using graphics This file is for private use only no hosting on web sites is allowed The file is property of BOO fiat bravo a owners organization and SvenJTD After you have done that you will need two connectors or do something similar same as what I have written to connect the position lights of the marea lights This is the connector you need Or you can use female speaker clamps like these The next step is to get a wire it must have two conducts that are in different colors or speaker wires with the red line on one of the cables So you can distinguish the wires Required length ca 40 50 cm or use more if you want This file is for private use only no hosting on web sites is allowed The file is property of BOO fiat bravo a owners organization and SvenJTD Connect the wire in the connector or the speaker clamps on one end On the picture are the speaker clamps After you have connected the speaker clamps to the wires You need to insulate them so they look like this If you have the connectors you wont need to do the following The bulb holder on the pictures isn t the marea light bulb holder but a side repeaters one so you can see the process After that take out the bulb holder and attach the clamps on the pins in the bulb holder like this This file is for private use only no hosting on web sites is allowed The file is property of BOO fiat bravo a owners organization and SvenJTD The next step is to insulate the bulb holder Here a hot glue gun was used but you can use silicone or duck tape or electrical tape The first pic is the hot glue gun method and the second the duck tape method If you have lights with no adjusting motors on them and need to switch them from your Bravo lights do the following.
Download
Showing posts with label Fiat. Show all posts
Showing posts with label Fiat. Show all posts
Friday, May 21, 2010
Wednesday, May 19, 2010
Fiat Brava Bravo 1.6 Schematic
Montare il miscelatore sul corpo farfallato Sonda Lambda a 4 fili Segnale sul filo nero Settare l emulazione del L E S su monoiniettore Bosch Segnale T P S sul filo n C arancio bianco Il filo della spia si trova in centralina sul Pin 9 Con LES 95 non collegare i fili gialli.
Fissare la massa del L E S sul polo negativo della batteria Scollegare la batteria prima di effettuare qualsiasi operazione Saldare le connessioni elettriche Non utilizzare rubacorrente MATERIALE CONSIGLIATO Set tubazioni e raccorderie Serbatoio G P L lt 54 supporto per Fiat Tipo NOTES Fix the mixer to the throttle body 4 wires Oxigen sensor Signal is on the black wire Switch LES emulation to Bosch single point position T P S signal is on wire C orange white Check engine lamp wire is on PIN 9 in the ECU With LES 95 do not connect yellow wires Connect L E S ground to the battery negative pole Disconnect the battery before working Soft solder wiring connections.
Download
Fissare la massa del L E S sul polo negativo della batteria Scollegare la batteria prima di effettuare qualsiasi operazione Saldare le connessioni elettriche Non utilizzare rubacorrente MATERIALE CONSIGLIATO Set tubazioni e raccorderie Serbatoio G P L lt 54 supporto per Fiat Tipo NOTES Fix the mixer to the throttle body 4 wires Oxigen sensor Signal is on the black wire Switch LES emulation to Bosch single point position T P S signal is on wire C orange white Check engine lamp wire is on PIN 9 in the ECU With LES 95 do not connect yellow wires Connect L E S ground to the battery negative pole Disconnect the battery before working Soft solder wiring connections.
Download
Tuesday, May 18, 2010
Fiat Brava Bravo 1.4 12V Schematic
Separate the throttle body and insert the mixer in the middle 4 wires Oxigen sensor Signal is on the black wire Switch LES emulation to Bosch singlepoint position T P S signal is on wire 4 Connect L E S ground to the battery negative pole Disconnect the battery before working Soft solder wiring connections Do not use fast connections OTHER SUGGESTED MATERIAL Pipes and fitting set 54 lt LPG tank tank fixing bracketts for Fiat Tipo NOTES Separer le groupe du monoinjecteur en y installant le melangeur au milieu Sonde lambda 4 fils Signal sur fil noir Positionner le micro switch du L E S sur la position monoinjection Bosch Signal TPS sur fil n 4 Fixer la masse du LES sur le p le negatif de la batterie D connecter la batterie avant d effectuer n importe quelle operation Souder les connections electriques Ne pas utiliser de connections rapides MATERIEL CONSEILLE Kit tuyaux et raccords R servoir G P L lt 54 support pour Fiat Tipo NOTAS Dividir el cuerpo del monoinycettor e instalar el mezclador en el medio Sonda Lambda con 4 cables se al en el cable negro Programar la simulaci n del Les en posici n monoinyector Bosch Se al T P S en el cable n 4 Fijar la masa del LES en el polo negativo de la bateria Desconectar la bater a antes de efectuar cualquier operaci n Soldar las conecciones el ctricas No utilizar conecciones r pidas MATERIAL ADICIONAL ACONSEJADO Set ca er as y racores Tanque G L P lt 54 soporte para Fiat Tipo Landi S r l si riserva di modificare la presente scheda senza alcun preavviso al fine di migliorare il funzionamento della vettura Landi S r l reserves the right to modify this specification sheet without previous notice in order to improve the vehicle performances.
Download
Download
Subscribe to:
Posts (Atom)