1986-93 Suzuki RM125 ESL450 Ignition/Lighting StatorFitting Instructions

Step 1:Take the ignition cover off. Are The Replacement Parts Similar? Compare the replacement part to the original. The replacement part should match, including the mounting hole locations. If not: Double check the application listing with your bike.
Step 2: Remove the flywheel using a proper puller. Remove the baseplate with the original stator. Disconnect the wires from the wiring loom.
Step 3: Remove existing stator coil off the baseplate and cut the wires close to the coil. Replace it with the new unit and feed the new leads though the holes in the baseplate.
Step 4: Screw the unit tight in position, as shown in the diagram, and make sure you use locking compound on the screws. TIGHTEN THE SCREWS SECURELY! Ignition Connections Suzuki RM: Connect the new BLACK lead to the original RED/ WHITE wire. Connect the new BLUE lead to the original BLACK/ RED wire. Honda CR: Connect the new BLACK lead to the original WHITE wire. Connect the new BLUE lead to the original RED wire. Yamaha YZ: Connect the new BLACK lead to the original BROWN wire. Connect the new BLUE lead to the original RED wire.
Step 5: Make sure the connections you make are good ones. Preferably you should crimp the wires using a high quality crimps. Otherwise use solder, but be aware that solder doesn’t work very well on older wiring. Lighting Connection Single YELLOW lighting output can be connected up straight to the lighting circuit. However it is better to use a 12V-AC regulator (ERG-200) parallel in circuit. The ground tag for the lighting coil can be hooked up under the base plate fitting screw. Take a look at our universal instructions for lighting coils for wiring details.
Step 6: On all applications, ensure the wires CANNOT TOUCH THE FLYWHEEL.

Download

Honda CBR 600RR/1000RR Sequential LED Tail Light Installation Guide

Installation Guide:
1. Removing factory tail light. Seat removal needed (2 alien bolts and slide it outj.Upper tail needs to be removed (4 alien bolts and gently pull up and back - remove left and right side covers first). Disconnect factory tail light harness.
2. Unscrew two screws holding bracket to upper tail. Remove bracket and swap over to new LED tail light. Take note the order of the washers. Locate and disconnect the factory signal connectors (blue and orange). Remove factory signals
3. Connect the sub harness shorter end to the blue and yellow wire respectively on the tail light, insulate with green cover. Connect main 3-wire harness.
4. Connect the longer end of sub harness: Blue/Black to the Honda orange connector Yellow/Black to the Honda blue connector. Secure sub harness with cable ties, etc and reverse procedure for reinstalling the tail lamp. Test all functions before re-assembling upper tail.

Download

Connecting to a wireless network using Microsoft® Windows Vista

After installing your wireless network adapter (please refer to product documentation for details), Windows Vista™ makes it very easy to connect to any wireless networks in range.
To begin, go to the Start Menu and click on Connect To:
This will bring up the Connect to a network window, which lists all networks Vista can currently connect to. This includes any dial-up connections that have been configured previously. Networks are usually listed either as Unsecured network or Security-enabled network.

In these cases, it will suffice to highlight the network you wish to connect to and click the Connect button at the bottom of the window. Windows will prompt you for a password if you are attempting to connect to a secured network.

It is possible that the settings stored on your computer will not match those of the wireless network, e.g. if a previously unsecured network has been secured. In this case, you will need to right-click on the network you wish to connect to and select Properties.

Download pdf Connecting to a wireless network using Microsoft® Windows Vista

VPN Set Up Guide for Windows Vista

1 - Open up the Control Panel from the Start Menu & double click on the Network & Internet Connections item.
2 - Under Networking and Sharing Center, Click on "Connect to a Network".
3 - Next, Click on "Set up a connection or Network."
4 - Select the "Connect to a Workplace" item at the bottom of the list and press Next >
5 - You will be asked, how do you want to connect? Select "Use my Internet Connection (VPN)"
6 - In the box labelled Internet address enter IP address provided in e-mail. In the box labelled Destination name enter "Libertyvpn", Unselect the first two check boxes and select the box "don't connect now, just set it up so I can connect later" Press Next >
7 - Now enter your Username, password, check "Remember this password" and press Create.
8 - The screen will show, "The connection is Ready to use" Click the "Close" button to return to the "Network and Internet" screen.
9 - In the Network and Internet screen, click on "Connect to a network" again.
10 - In the Connect to a Network screen, you should see the Libertyvpn connection that we have set up. Right-click on the Libertyvpn connection and choose "Properties" from the menu that appears.
11 - From the Properties, click on the "Options" tab. Make sure the checkbox labelled "Include Windows logon domain" is unchecked. Then click the "PPP Settings." button. Make sure that Only "Negotiate multi-link connections" is unchecked
12 - From the Properties, click on the "Security" tab. The security option should be "Typical", "Require Secured Password" and ONLY check "require data encryption"

Download pdf VPN Set Up Guide for Windows Vista