Showing posts with label foot pounds. Show all posts
Showing posts with label foot pounds. Show all posts

Tuesday, May 11, 2010

HONDA CRF450X Flywheels Installation Instructions

INSTALL FLYWHEEL
1. Drain 20% of the oil from the bike first.
2. Shut the gas supply off on the bike, then lay it over on its side. A small amount of gas will leak from the overflow tubes when the bike is first laid down.
3. Remove shifter.
4. Remove bolts holding the side cover on (no need to remove one of the oil filter bolts).
5. Remove oil fill cap.
6. Disconnect clutch cable and lay cable out of the way.
7. Remove side case and lay it next to the main case to avoid removing any wires. TAKE CARE - do not allow the two alignment pins to come loose from the side case. They CAN stay in the side case or in the main case, but you don’t want them to fall out and get lost; or, even worse, dropped in the oil for later consumption by the motor!!
8. Use a 17mm deep socket and impact ratchet to remove the flywheel retaining nut. If an air ratchet is not available, hold the rear wheel while removing the 17mm flywheel nut. Note: If a Deep socket is not used damage to the crankshaft oiler may occur.
9. Use flywheel puller to remove the flywheel. Remember to install protective nut on to crankshaft to avoid damage to end of flywheel. Note: there is a small hole on the shaft that allows for oil flow to the crankshaft - using the correct flywheel puller will protect this hole.
10. Install new flywheel and torque flywheel bolt to manufactureer specification. Do not use thread locking compound. Use the woodruff key on the crank to line up the keyway on the flywheel with the crankshaft.
11. For ease of assembly, connect clutch cable before installing bolts.
12. Replace the side case. Use a new gasket if necessary. Torque side case bolts to 7 foot pounds. Do not overtighten these bolts! Replace the shifter. Make sure the bolt threads in smoothly - cross threading is easy. You will need a Honda CRF flywheel puller (TT part# 6600-P02) for this installation. An impact ratchet is also highly recommended.

Note: Trail Tech CRF450X flywheel is provided with one M6×25MM BHCS to replace the timing chain guide bolt (A), and a M6×12 BHCS to replace the guide retainer bolt (B). These bolts allow for the flange on the exterior of the flywheel to clear the fasteners. Trail Tech is not liable for any damage due to the improper installation or lack of installation of these bolts. Contact Trail Tech Tech-Support for further questions.

Download

Sunday, July 13, 2008

Spin-On By-Pass Filter Installation and Servicing Instructions

Attaching the filter mount
1. Survey the engine compartment for possible mounting locations. Solid structures such as the firewall, fender well, radiator support or frame are normal locations. (Do not mount on engine.) Refer to diagram B for minimum area requirements and consider accessibility for servicing.
2. Refer to diagram A for preferred mounting positions.
3. When the location has been determined, use the mounting template provided to locate and mark mounting holes. This can be easily done with a center punch and hammer.
4. Install adapter fittings (BP-208) on filter mount using provided thread sealant as noted in diagram C. If desired, 90° angle fitting (BP-52) may also be used. Using a 7⁄16 wrench, tighten fittings 2-3 turns beyond finger tight. Keep in mind the direction you wish to have the hoses intersect the mount.
5. With a 5⁄16 drill bit, drill out the previously marked mounting holes and attach the mount using the 5⁄16 bolts, nuts, small washer and fender washers provided. Bolts should be tightened to 16-18 foot pounds. 1/2 wrenches or socket will be required for this operation.
6. Fill the By-Pass Filter element with the same motor oil being used in the vehicle. Lubricate the filter gasket with oil and spin filter onto mount. Tighten per instruc- tions on the filter.

Download