Showing posts with label voltage. Show all posts
Showing posts with label voltage. Show all posts

Friday, May 21, 2010

1988 Mercedes Benz 300CE (124 Chassis) Connecting Test Equipment and Reading Diagnostic Trouble Codes

Testing with the impulse counter should be carried out for rapid fault diagnosis. The
impulse counter output shows only existing faults, since the ACC system does not have
memory capabilities. If one or more faults are indicated, repair as necessary and repeat
the test. Be sure that fuse #7 is good, the battery voltage is between 11-14 volts and the
temperature selector wheel is set to 22°C.
1. Connect the impulse counter to the on-board diagnostic connector.
Black lead of the impulse counter to socket 1
Yellow lead of the impulse counter to socket 7
Red lead of the impulse counter to battery positive terminal.
2. Turn the ignition to the "ON" position.
The LED "U Batt" will be illuminated. If the LED "U BATT" does not illuminate,
check for voltage between socket 1 of the on-board diagnostic connector and
the positive terminal of the battery. If the voltage is not between 11-14 volts,
check for an open circuit or loose ground connection.
Test for voltage between socket 7 and socket 1 of the diagnostic connector.
The voltage should be 6 - 12 volts.
3. Depress the start button for 2 - 4 seconds.
Fault codes will be indicated by the number in the impulse counter display
window. Take note of the impulse display number.
Faults are displayed in ascending order.
The number 1 indicates that no faults are stored in memory.
During the impulse readout, The LED indicator in the fresh air/recirculation
switch will blink.
4. Repeat step 3 until all faults are indicated. After all fault codes have been
displayed, pushing the start button again for 2 - 4 seconds will repeat the fault code
readout sequence.

Source

Thursday, May 6, 2010

99-00 Honda Civic SI-B16A2 Boost Upgrade Installation Instructions

This kit has been engineered to be an easy, bolt on upgrade to your standard Jackson Racing supercharger kit. It will raise your boost approximately 2 psi. As such, it has been designed to be a “Race Only” kit. Because of the “Race Only” design criteria, the C.A.R.B. Exemption Order number supplied with your Jackson Racing Supercharger Kit does NOT cover this product. Therefore, this racing boost upgrade is legal in California only on racing vehicles, which may never be used upon a highway. Other states may have laws governing the use of this product. Check local regulations before installation. Our kit was designed with and performs best when used with a good header, cat-back exhaust, and a good high flow air filter. Other non-specified accessories or engine components may affect your specific boost and horsepower output.

A qualified technician should install this Boost Upgrade Kit. Although it has been designed to be easily installed, every racing modification should be tuned and tested with the proper tuning equipment. We require that any cut wires be soldered and shrink wrapped for protection. This will ensure that all connections are solid and stable.

For the “Do It Yourself” installer, the following tuning hints can help you verify if your vehicle is performing properly or needs further help. Any vehicle that has an Oxygen Sensor (O2) can test its air to fuel ratio (air/fuel) using a standard digital voltmeter.

Connect the positive side of your volt-meter into the signal output wire on your O2 sensor. Connect your voltmeter ground wire to a good chassis ground. At Wide Open Throttle (WOT), with the car completely warmed up, you should be reading voltage from the O2 sensor of .84v (approximately 13-1 air/fuel ratio) to a voltage of .93v (approximately 12-1). A reading of .90 is preferred, but a voltage fluctuation from slow RPM to high RPM is normal. Do not expect the voltage to stay at one continuous level throughout the entire test. In some cases you will have a slightly over rich mixture at low speed in trade for a good even mixture at high speed.

Download

Monday, August 11, 2008

Power Quality Monitoring and Power Metering Tutorial

Power generation and transmission today are accomplished using three phase alternating-current. To understand electrical power quality monitoring and electrical power metering you must first have a basic understanding of three-phase power.

Electricity Basics
As a mechanical engineer, my favorite explanation of power is the analogy of a water system. In a water system you have a pipe that can carry water. The larger the pipe the more water it can carry. To move the water through the pipe you need to pressurize the water and when the water has the ability to move from a high pressure area to a low pressure area (like when you open a valve) you get flow. In our electrical analogy we replace the pipe with a wire. Instead of carrying water the wire carries electrons. The larger the wire the more electrons it can carry. You pressurize the electrons by applying voltage. When the circuit is complete the electrons will flow from the high voltage to the lower voltage and you get flow, know as current.

In a DC circuit the voltage and current will be constant (with a constant load). However in an AC circuit the voltage and the current will vary in a sinusoidal manner. The instantaneous voltage and current levels will vary over time based on their phase.

Download