The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.
NOTE:
• Be careful not to damage the body paint finish.
• Body side moldings should only be installed if the ambient air temperature is 15°C (60°F) or above.
• To allow the adhesive to cure, do not wash the vehicle for 24 hours. Please advise the customer.
• These installation instructions show the left body side moldings being installed. The same procedure applies to installing the right body side moldings.
1. Using one alcohol swab, clean the area where the left body side molding will attach.
2. Align the front template to the left front door and attach the template to the door using strips of masking tape.
3. Place the left front body side molding against the template to verify the installation position on the left front door. Remove the body side molding.
4. Peel back approximately 1½ to 2 inches of adhesive backing from each adhesive tape, and tape the ends to the front surface of the body side molding. Remove the small end pieces of the adhesive backing.
5. Align the left front body side molding with the front template, and attach it to the left front door. If the vehicle has door edge film installed, align the end with the door edge film.
Download
Showing posts with label ambient air temperature. Show all posts
Showing posts with label ambient air temperature. Show all posts
Sunday, May 9, 2010
Friday, March 26, 2010
2008 Honda Accord 2-Door Trunk Spoiler Installation Instructions
The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
NOTE:
• Be careful not to damage the body paint finish.
• This trunk spoiler kit should be installed only if the ambient air temperature is 60°F (15°C) or above.
• Wash and wax the area to be covered. Use a
high-quality paste wax.
Installing the Trunk Spoiler
1. Make sure you have the anti-theft codes for the radio and navigation system (if equipped), then write down the radio station presets.
2. Disconnect the negative cable from the battery.
3. On the inside of the trunk lid, locate the two identification marks on the trunk lid. Lightly center-punch each mark. Repeat on the right side of the trunk lid.
4. While wearing eye protection, first drill the hole with a 3 mm drill bit, and finish with an 8 mm drill bit.
• To prevent drilling through the trunk lid, wrap a drill stop around the drill bit 10 mm away from the tip.
• To prevent the metal shavings from falling onto the trunk floor, place a cover onto the trunk floor.
• Remove all burrs and metal shavings with a file, and apply touch-up paint to the edges of the holes you drilled.
• Repeat on the right side of the trunk lid.
5. Close the trunk lid. Attach tape to the trunk lid as shown.
6. Align the template with the left side trunk lid. Using a felt-tip pen, mark the left side trunk lid as shown. Remove the template.
7. Flip the template over. Align the template with the right side trunk lid. Using a felt-tip pen, make two marks on the right side trunk lid as shown. Remove the template.
8. Center-punch the mark on the left side trunk lid. While wearing eye protection, first drill the hole with a 3 mm drill bit, and finish with an 8 mm drill bit.
Remove the tape.
• To prevent drilling through the trunk lid, wrap a drill stop around the drill bit 10 mm away from the tip.
• Remove all burrs and metal shavings with a file, and apply touch-up paint to the edges of the holes you drilled.
• Take care not to damage the wire harnesses when drilling the holes.
Download
NOTE:
• Be careful not to damage the body paint finish.
• This trunk spoiler kit should be installed only if the ambient air temperature is 60°F (15°C) or above.
• Wash and wax the area to be covered. Use a
high-quality paste wax.
Installing the Trunk Spoiler
1. Make sure you have the anti-theft codes for the radio and navigation system (if equipped), then write down the radio station presets.
2. Disconnect the negative cable from the battery.
3. On the inside of the trunk lid, locate the two identification marks on the trunk lid. Lightly center-punch each mark. Repeat on the right side of the trunk lid.
4. While wearing eye protection, first drill the hole with a 3 mm drill bit, and finish with an 8 mm drill bit.
• To prevent drilling through the trunk lid, wrap a drill stop around the drill bit 10 mm away from the tip.
• To prevent the metal shavings from falling onto the trunk floor, place a cover onto the trunk floor.
• Remove all burrs and metal shavings with a file, and apply touch-up paint to the edges of the holes you drilled.
• Repeat on the right side of the trunk lid.
5. Close the trunk lid. Attach tape to the trunk lid as shown.
6. Align the template with the left side trunk lid. Using a felt-tip pen, mark the left side trunk lid as shown. Remove the template.
7. Flip the template over. Align the template with the right side trunk lid. Using a felt-tip pen, make two marks on the right side trunk lid as shown. Remove the template.
8. Center-punch the mark on the left side trunk lid. While wearing eye protection, first drill the hole with a 3 mm drill bit, and finish with an 8 mm drill bit.
Remove the tape.
• To prevent drilling through the trunk lid, wrap a drill stop around the drill bit 10 mm away from the tip.
• Remove all burrs and metal shavings with a file, and apply touch-up paint to the edges of the holes you drilled.
• Take care not to damage the wire harnesses when drilling the holes.
Download
Subscribe to:
Posts (Atom)