Showing posts with label body. Show all posts
Showing posts with label body. Show all posts

Wednesday, May 19, 2010

2001-02 Saturn SL1 Automatic Transmissions Saturn MP6 & MP7 Overhaul

Disassembly 1. Remove line actuator cover bolts. See Fig. 53 . Carefully remove cover and connector plate. Remove line actuators by twisting line actuator as it is pulled from valve body. 2. Remove through bolts. Separate valve body and separator plate. Remove check balls. See Fig. 54 . Remove manual valve. Remove each valve assembly. Retain in proper order for reassembly. See Fig. 55 and Fig. 56 .
Inspection
Inspect valves for scoring, nicks and scratches. Inspect springs for damaged or distorted coils. For spring free length specifications, see VALVE BODY SPRING SPECIFICATIONS table. Using a No. 43 (2.25 mm) drill bit, insert drill bit shank into connector plate terminals. Ensure drill bit drags slightly in each terminal. If bit does not drag slightly, replace connector plate. Inspect valve body casting for porosity, interconnected fluid passages and damaged machined surfaces.

Source

Tuesday, May 18, 2010

Body Badge Installation

The badges are made from layers of foil and other materials, all covered with a pliable urethane clear “lens.” They are thin, not more than 1/16 inch thick, so they are very slick and appear to have been molded right into the painted surface of the body work. In comparison, the raised stock badges and aftermarket versions look rather crude. Since the badge colors match the various car colors perfectly, the integrated appearance of the badges is all the more striking. Depending on the color of your car and the color of the badge you chose, the end result could be very subtle and sophisticated or more striking. To avoid mistakes, please read these directions fully before beginning.

Required items:
• Xenit Adhesive remover from Stoner, or 3M Adhesive Remover available from your local auto store
• Waxed dental floss
• General purpose masking tape
• Soft cotton detailing towel
• Isopropyl Alcohol and cotton balls or alcohol swabs
• Optional: aftermarket finishing/detailing spray, we use Zaino’s Z-6.

Quick Installation Instructions
The adhesive of the badges cures better when the temperature is 70ยบ or higher. It has been reports that installation can/has been done at lower temperatures with out any problems.
1. Clean the badge and sounding areas to remove all dirt, dust, oils, etc.
2. Remove the stock badges.
3. Clean the badge location by wiping with clean towel and isopropyl alcohol.
4. Remove the backing from the S Badge and apply the adhesive side to the clean, dry surface. Use a rolling manner (from bottom to top) to prevent air bubbles. Using caution contaminate the adhesive on the back of the emblem.

Download

Tuesday, May 11, 2010

2002 Ford E450 Cutaway Owners Manual

Remove the attached body, if applicable. Remember to disconnect all electrical connections to the body, and fuel filler tube, before removing the body. The installation can also be completed using a lift to raise the vehicle. If using a lift, chassis body removal may not be necessary but removal of rear wheels will aid in installation.

Download

Sunday, May 9, 2010

2010 Insight Body Side Molding Installation Instructions

The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.

NOTE:
• Be careful not to damage the body paint finish.
• Body side moldings should only be installed if the ambient air temperature is 15°C (60°F) or above.
• To allow the adhesive to cure, do not wash the vehicle for 24 hours. Please advise the customer.
• These installation instructions show the left body side moldings being installed. The same procedure applies to installing the right body side moldings.

1. Using one alcohol swab, clean the area where the left body side molding will attach.
2. Align the front template to the left front door and attach the template to the door using strips of masking tape.
3. Place the left front body side molding against the template to verify the installation position on the left front door. Remove the body side molding.
4. Peel back approximately 1½ to 2 inches of adhesive backing from each adhesive tape, and tape the ends to the front surface of the body side molding. Remove the small end pieces of the adhesive backing.
5. Align the left front body side molding with the front template, and attach it to the left front door. If the vehicle has door edge film installed, align the end with the door edge film.

Download

Friday, May 7, 2010

1993 Toyota Pickup 22RE 3VZ-E Factory Service Manual

This guide cover about Introduction how to use this manual, troubleshooting, precaution, maintenance, Engine Ignition, Starting System, Charging System, Service Specs, Clutch, Manual Transmission, Automatic Transmission, Transfer, Propeller Shaft, Suspension and Axle, Brake System, Steering, Body Electrical, Body Mechanical, Air Conditioning. Maintenance Schedule Maintenance Operations General Maintenance. Engine mechanical description, troubleshooting, tune up procedure, Compression Check, Cylinder Head, Exhaust System, Service Specifications.

MFI system precaution, troubleshooting and diagnosis, Cooling System-Coolant Check and Replacement. Cooling System–Water Pump, Cooling System–Service Specifications. Ignition Description Precautions System Circuit Operation Preparation On Vehicle Inspection Distributor Service Specifications. Body Electrical : General Information Power Source Ignition Switch Lighting System Wiper and Washer System Combination Meter Power Window Control System Power Door Lock Control System Power Mirror Control System Cruise Control System Audio System. Body Mechanical : General Information Hood Front Door Moulding Windshield Back Window Quarter Window (X-Cab) Moon Roof Instrument Panel One-Touch Tail Gate Seat Seat Belt Body Dimensions.

Download

Thursday, May 6, 2010

1999 Nissan Quest Owners Manual.pdf

Turn the ignition key to the OFF position and secure the steering wheel in a straight ahead position with a rope or similar device Never place the ignition key in the LOCK position This will result in damage to the steering lock mechanism Move the gearshift lever to the N Neutral position When towing with the rear wheels on the ground release the parking brake.

Attach safety chains for all towing 6 12 In case of emergency ACE1029 NISSAN recommends that your vehicle be towed with the driving front wheels off the ground as illustrated Speed Below 60 MPH 97 km h Distance Less than 500 miles 800 km In case of emergency 6 13 CAUTION Never tow the vehicle with the rear wheels raised with the front wheels on the ground as this may cause serious and expensive damage to the transmission If it is necessary to tow the vehicle with the rear wheels raised always use towing dollies under the front wheels If you have to tow the vehicle with four wheels on ground observe the following restricted towing speeds and distances Speed Below 30 MPH 50 km h Distance Less than 40 miles 65 km Never tow the vehicle from the rear i e backward with four wheels on the ground as this may cause serious and expensive damage to the transmission Do not tow with a sling type truck either from the front or the rear It may cause body damage Never utilize the rear tie down brackets or slots to tow another vehicle as this may cause body damage VEHICLE RECOVERY freeing a stuck vehicle Tow chains or cables must only be attached to the main structual members of the vehicle Pulling devices should be routed so they do not touch any part of the suspension steering brake or cooling systems Always pull the cable straight out from the front or rear of the vehicle Never pull the vehicle at an angle Pulling devices such as ropes or canvas straps are not recommended for use in vehicle towing or recovery Stand clear of a stuck vehicle WARNING Do not spin your tires at high speed This could cause them to explode and result in serious injury Parts of your vehicle could also overheat and be damaged 6 14 In case of emergency 7 Appearance and care Cleaning exterior and interior 7 2 Corrosion protection 7 4 CLEANING EXTERIOR AND INTERIOR when dust or mud builds up on the surface Whenever possible store or park your vehicle inside a garage or in a covered area When it is necessary to park outside park in a shady area or protect the vehicle with a body cover Be careful not to scratch the paint surface when putting on or removing a body cover Avoid using tight napped or rough cloths such as washing mitts Care must be taken when removing caked on dirt or other foreign substances so the paint surface is not scratched or damaged Rinse the vehicle thoroughly with plenty of clean water Inside flanges seams and folds on the doors hatches and hood are particularly vulnerable to the effects of road salt Therefore these areas must be regularly cleaned Take care that the drain holes in the lower edge of the door are open.

Download

Monday, May 3, 2010

Acura GSR Whirlwind Intake Manifold Instructions

Removal
1. Relieve the fuel pressure in the system by loosening the banjo bolt on the top of the fuel filter. Disconnect the fuel line from the fuel rail. It is a good idea to replace the washers. Disconnect the fuel harness holder and unbolt. Disconnect the hoses from the fuel pressure regulator (FPR).
2. Disconnect intake hose/pipe from throttle body. Disconnect all hoses leading to the throttle body and intake manifold. Disconnect throttle cable bracket on manifold and throttle cable from throttle body. Disconnect the cables to the the throttle position sensor (TPS) and the map sensor on the throttle body.
3. Unbolt two lower intake manifold bolts that secure manifold to engine block. This bracket willl still be used to accommodate the heater bypass pipe. Unbolt manifold from engine block. Remove manifold, throttle body, and fuel rail as one unit.
4. Remove the intake air bypass (IAB) vacuum tank, check valve and control solenoid unit. Due to the different design of your new manifold, these parts will no longer be used. Do not remove the FPR hose. This hose will be used in the re-installation process.
5. Unbolt throttle body from manifold. Inspect gasket and replace if needed. Unscrew throttle body studs from flange of manifold. Remove fuel rail assembly from manifold.
6. From original manifold, unbolt and remove idle air control valve (IAC), intake air temperature valve (IAT), and o-rings. Replace o-rings if needed. Remove fuel rail studs from original manifold.

Assembly
1. Screw throttle body studs and fuel rail studs removed from original manifold into the new Power+Plus Manifold.
2. Bolt throttle body to new manifold. When positioning throttle body gasket, the U-shaped portion is in top left corner of flange.
3. Bolt idle air control valve, intake air temperature valve with o-rings to new manifold. Install fuel rail, making sure o-rings are positioned correctly to prevent fuel leakage.
4. Position new manifold assembly with throttle body and fuel rail back on the cylinder head over the studs, making sure new intake gasket is properly positioned. Connect the EVAP purge control solenoid valve. Due to the new intake manifold design, there is no mounting location for for the EVAP purge control solenoid valve. It can be zip-tied to a secure location. For 1994-’95 vehicles, one hose end will plug into the charcoal canister and the other hose end will plug into the small vacuum fitting located onthe rear of the new intake manifold. For 1996-01 vehicles. see notes below.
5. Bolt on the fuel injector harness holder and hoses, connecting the harness to the injectors. Connect TPS, map sensor, and fuel line. The FPR hose will connect to the small vacuum fitting that was originally on the front of the manifold but is now on the back. Tighten banjo bolt on top of fuel filter.
6. Use the new supplied throttle cable bracket to hook up stock throttle cable to the throttle body.
7. Connect battery and replace coolant. Cap off any unused vacuum tubes with vacuum caps.
8. Start engine, check for leaks. After engine is brought to operating temperature, shut it off and check that all nuts and bolts are tight. Retighten manifold bolts after 500 miles.

Download

Saturday, May 1, 2010

1994 Subaru Impreza Service Manual

Engine section : on car service, engine (DOHC), engine lubrication system, fuel injection system, fuel system, exhaust system, clutch, engine and transmission mounting system, transmission and differential section : manual transmission and differential, automatic transmission and differential, AWD system.

Mechanical components section : Suspension, wheels and axles, steering system, brakes, pedal system and control cables, Air conditioning system. Body section : body and exterior, instrument panel, supplement restraint system. Electrical system : body electrical system. Diagnostics system : fuel injection system, body electrical system, wiring diagram. Schedule of inspection and maintenance services : Drive belts, except camshaft, inspect drive belt tension, Camshaft drive belt (Timing Belt), engine oil, engine oil filter, replace engine coolant and inspect cooling system, hoses and connections, replace fuel filter and inspect fuel system, lines and connections, Air cleaner element, Spark plugs. Automatic transmission flud, brake fluid. Service procedure : precaution, on-car service, performance test, overall transmission, reduce drive gear assembly, control valve body, oil pump assembly, drive pinion shaft, reverse clutch, high clutch, forward clutch, high clutch, Differential case assembly.

Download