his kit is designed to fit both the 120&160 engine platforms. The only difference you will find between the 120 and the 160 engine is the direction the cable adjustment block is installed on the engine block.
1. Remove the stamped factory linkage plate and related hardware.
2. Check your carburetor and confirm the throttle arm (black plastic molded arm on the top of the throttle shaft) is in good working condition.
3. Install the Linkage Bridge to your engine using the two supplied metric socket head bolts. A drop of thread locking compound on each bolt is recommended to prevent bolts from coming loose from vibration and harmonics.
4. Install the Cable Adjustment Block to the engine using the factory bolt that was removed in step 1.
5. Bolt the Linkage Arm to the Linkage Bridge using the supplied Shoulder Bolt. Use a small drop of thread locking compound on the threads.
6. The Throttle Stop Eccentric can now be bolted to the Linkage Bridge using the supplied button head bolt. Do Not fully tighten the bolt until the final step. This eccentric is used as a throttle stop to prevent broken or worn carburetor parts as well as to set wide open throttle to the best performance position.
7. Bend your Linkage Rod to fit from the Linkage Arm to the throttle arm on the carburetor. It is important this fits proper to prevent linkage failure. We have formed one end of the linkage rod to fit the Linkage Arm. Each application is slightly different and will require the user to complete the bending on the throttle arm end.
Download
Showing posts with label throttle. Show all posts
Showing posts with label throttle. Show all posts
Thursday, May 20, 2010
Monday, May 3, 2010
Acura GSR Whirlwind Intake Manifold Instructions
Removal
1. Relieve the fuel pressure in the system by loosening the banjo bolt on the top of the fuel filter. Disconnect the fuel line from the fuel rail. It is a good idea to replace the washers. Disconnect the fuel harness holder and unbolt. Disconnect the hoses from the fuel pressure regulator (FPR).
2. Disconnect intake hose/pipe from throttle body. Disconnect all hoses leading to the throttle body and intake manifold. Disconnect throttle cable bracket on manifold and throttle cable from throttle body. Disconnect the cables to the the throttle position sensor (TPS) and the map sensor on the throttle body.
3. Unbolt two lower intake manifold bolts that secure manifold to engine block. This bracket willl still be used to accommodate the heater bypass pipe. Unbolt manifold from engine block. Remove manifold, throttle body, and fuel rail as one unit.
4. Remove the intake air bypass (IAB) vacuum tank, check valve and control solenoid unit. Due to the different design of your new manifold, these parts will no longer be used. Do not remove the FPR hose. This hose will be used in the re-installation process.
5. Unbolt throttle body from manifold. Inspect gasket and replace if needed. Unscrew throttle body studs from flange of manifold. Remove fuel rail assembly from manifold.
6. From original manifold, unbolt and remove idle air control valve (IAC), intake air temperature valve (IAT), and o-rings. Replace o-rings if needed. Remove fuel rail studs from original manifold.
Assembly
1. Screw throttle body studs and fuel rail studs removed from original manifold into the new Power+Plus Manifold.
2. Bolt throttle body to new manifold. When positioning throttle body gasket, the U-shaped portion is in top left corner of flange.
3. Bolt idle air control valve, intake air temperature valve with o-rings to new manifold. Install fuel rail, making sure o-rings are positioned correctly to prevent fuel leakage.
4. Position new manifold assembly with throttle body and fuel rail back on the cylinder head over the studs, making sure new intake gasket is properly positioned. Connect the EVAP purge control solenoid valve. Due to the new intake manifold design, there is no mounting location for for the EVAP purge control solenoid valve. It can be zip-tied to a secure location. For 1994-’95 vehicles, one hose end will plug into the charcoal canister and the other hose end will plug into the small vacuum fitting located onthe rear of the new intake manifold. For 1996-01 vehicles. see notes below.
5. Bolt on the fuel injector harness holder and hoses, connecting the harness to the injectors. Connect TPS, map sensor, and fuel line. The FPR hose will connect to the small vacuum fitting that was originally on the front of the manifold but is now on the back. Tighten banjo bolt on top of fuel filter.
6. Use the new supplied throttle cable bracket to hook up stock throttle cable to the throttle body.
7. Connect battery and replace coolant. Cap off any unused vacuum tubes with vacuum caps.
8. Start engine, check for leaks. After engine is brought to operating temperature, shut it off and check that all nuts and bolts are tight. Retighten manifold bolts after 500 miles.
Download
1. Relieve the fuel pressure in the system by loosening the banjo bolt on the top of the fuel filter. Disconnect the fuel line from the fuel rail. It is a good idea to replace the washers. Disconnect the fuel harness holder and unbolt. Disconnect the hoses from the fuel pressure regulator (FPR).
2. Disconnect intake hose/pipe from throttle body. Disconnect all hoses leading to the throttle body and intake manifold. Disconnect throttle cable bracket on manifold and throttle cable from throttle body. Disconnect the cables to the the throttle position sensor (TPS) and the map sensor on the throttle body.
3. Unbolt two lower intake manifold bolts that secure manifold to engine block. This bracket willl still be used to accommodate the heater bypass pipe. Unbolt manifold from engine block. Remove manifold, throttle body, and fuel rail as one unit.
4. Remove the intake air bypass (IAB) vacuum tank, check valve and control solenoid unit. Due to the different design of your new manifold, these parts will no longer be used. Do not remove the FPR hose. This hose will be used in the re-installation process.
5. Unbolt throttle body from manifold. Inspect gasket and replace if needed. Unscrew throttle body studs from flange of manifold. Remove fuel rail assembly from manifold.
6. From original manifold, unbolt and remove idle air control valve (IAC), intake air temperature valve (IAT), and o-rings. Replace o-rings if needed. Remove fuel rail studs from original manifold.
Assembly
1. Screw throttle body studs and fuel rail studs removed from original manifold into the new Power+Plus Manifold.
2. Bolt throttle body to new manifold. When positioning throttle body gasket, the U-shaped portion is in top left corner of flange.
3. Bolt idle air control valve, intake air temperature valve with o-rings to new manifold. Install fuel rail, making sure o-rings are positioned correctly to prevent fuel leakage.
4. Position new manifold assembly with throttle body and fuel rail back on the cylinder head over the studs, making sure new intake gasket is properly positioned. Connect the EVAP purge control solenoid valve. Due to the new intake manifold design, there is no mounting location for for the EVAP purge control solenoid valve. It can be zip-tied to a secure location. For 1994-’95 vehicles, one hose end will plug into the charcoal canister and the other hose end will plug into the small vacuum fitting located onthe rear of the new intake manifold. For 1996-01 vehicles. see notes below.
5. Bolt on the fuel injector harness holder and hoses, connecting the harness to the injectors. Connect TPS, map sensor, and fuel line. The FPR hose will connect to the small vacuum fitting that was originally on the front of the manifold but is now on the back. Tighten banjo bolt on top of fuel filter.
6. Use the new supplied throttle cable bracket to hook up stock throttle cable to the throttle body.
7. Connect battery and replace coolant. Cap off any unused vacuum tubes with vacuum caps.
8. Start engine, check for leaks. After engine is brought to operating temperature, shut it off and check that all nuts and bolts are tight. Retighten manifold bolts after 500 miles.
Download
Sunday, July 13, 2008
Installation & Tuning Instructions For all Motorcycle Applications
Thank you for choosing PowerCard, with its unique load-based digital fueling technology. Please read through and understand these instructions before attempting installation. In order to further familiarize yourself with your new PowerCard, you may want to experiment with the interactive PowerCard demos online at PowerCardTuning.com. To get the most from your PowerCard, it is important to recognize the difference between “load,” and throttle position/RPM. For example, put your motorcycle in first gear and hold the throttle wide-open, then do the same thing in fifth. Notice how the rate of RPM change is much faster in first gear than in fifth.
This is because the load in fifth gear is much higher. Any given combination of throttle position and RPM can be associated with vastly different loads. PowerCard recognizes this, and uses proprietary algorithms to apply the right amount of additional fuel in the right circumstance. The PowerCard technology is unique because it is load based and does not rely solely on throttle position and RPM; it determines load based on the output from the factory programmed ECU, which has had thousands of hours of development and uses many sensors. Once the PowerCard "knows the load", you can adjust it to provide the extra fuel needed to get maximum performance from your modifications.
What PowerCard Does
PowerCard adds fuel. When you modify your intake/engine/exhaust, the stock engine management may not be able to handle the fueling requirements of increased air flow. PowerCard gives you control of additional “cruise” or low load (green), transition (yellow) and high load (red) fuel, and the transition points between these modes, in order to get the most out of your engine modifications. In carburetor terms, think of these as idle, accelerator pump and main jet circuits.
What PowerCard Does Not Do
PowerCard cannot delete fuel. If you are having idle problems with oversize injectors, PowerCard cannot fix this problem. Also, once an injector reaches 100 percent duty cycle, it will not be possible for PowerCard to add any more fuel. You will need to either increase fuel pressure, or move to larger injectors.
Download
This is because the load in fifth gear is much higher. Any given combination of throttle position and RPM can be associated with vastly different loads. PowerCard recognizes this, and uses proprietary algorithms to apply the right amount of additional fuel in the right circumstance. The PowerCard technology is unique because it is load based and does not rely solely on throttle position and RPM; it determines load based on the output from the factory programmed ECU, which has had thousands of hours of development and uses many sensors. Once the PowerCard "knows the load", you can adjust it to provide the extra fuel needed to get maximum performance from your modifications.
What PowerCard Does
PowerCard adds fuel. When you modify your intake/engine/exhaust, the stock engine management may not be able to handle the fueling requirements of increased air flow. PowerCard gives you control of additional “cruise” or low load (green), transition (yellow) and high load (red) fuel, and the transition points between these modes, in order to get the most out of your engine modifications. In carburetor terms, think of these as idle, accelerator pump and main jet circuits.
What PowerCard Does Not Do
PowerCard cannot delete fuel. If you are having idle problems with oversize injectors, PowerCard cannot fix this problem. Also, once an injector reaches 100 percent duty cycle, it will not be possible for PowerCard to add any more fuel. You will need to either increase fuel pressure, or move to larger injectors.
Download
Subscribe to:
Posts (Atom)