Showing posts with label Ford. Show all posts
Showing posts with label Ford. Show all posts

Friday, May 21, 2010

1993 Bronco/Econoline/F-Series Evaporator Case Assembly Workshop Manual

Evaporator Case Assembly The evaporator case assembly is attached to the engine side of the dash panel. The case is a two-piece molded construction, one piece of which forms a cover over the evaporator core. An integral vacuum reservoir is part of the cover housing. This reservoir and the vacuum motor, which operates the outside/recirc air door, are linked through a check valve to a hose that supplies engine vacuum. The blower housing is an integral part of the evaporator case. It houses the blower motor and wheel assembly which attaches to the case through a mounting flange on the blower motor. The blower motor resistor assembly is attached to the case with its thermal elements extending into the air stream inside the evaporator case. The suction accumulator/drier is attached to the evaporator core by a support bracket.
Evaporator Case Assembly, Disassembled View Plenum Assembly The plenum assembly is mounted to the dash panel in the passenger compartment. It contains the heater core, temperature blend door, panel door and the floor/defrost door. The temperature blend door is cable-controlled through a cam located on top of the plenum. The panel and floor/defrost doors are both controlled by vacuum motors, located on the bottom of the plenum. The heater core is located in the plenum behind the heater core cover. The cover allows the core to be removed without removing the plenum. Plenum Assembly.

Source

Monday, May 17, 2010

1987-1991 Light Truck Bronco F-150-350 Series Service Manual

The wide ratio version is available for all F Series vehicles over 8500 lbs GVW all engines 6007 except F Super Duty Commercial Stripped Chassis equipped with a diesel engine The close ratio version is available only in F Series vehicles with a 7 3L diesel engine and a GVW over 8500 lbs.

The ratios are as follow 1st 4 14 5 72 2nd 2 37 2 94 3rd 1 42 1 61 4th 1 0 1 0 5th 0 77 0 76 Reverse 3 79 5 24 Close Ratio Diesel Wide Ratio Gasoline Diesel The transmission features an aluminum case 7005 with an integral clutch housing Because of the aluminum case the tapered roller bearings of the transmission shafts must be fitted under preload This is because heat expansion of the aluminum case is greater than that of the steel alloy mainshaft and countershaft cluster gear 7113 If the bearings were not pre loaded this would result in excessive end play when the case in warm loaded operating conditions The transmission also features shrink fit gears on the countershaft cluster gear Shrink fit gears are connected to the countershaft cluster gear by friction only rather than connected trough splines The gear is heated and lightly pressed onto the countershaft cluster gear The subsequent cooling of the gear provides the shrink fitting The countershaft cluster gear is serviced as an assembly 07 03B 1 1994 Econoline F 150 F 250 F 350 Bronco F Super Duty Powertrain Drivertrain Aug 1993 TRANSMISSION ZF S5 42 TROUBLESHOOTING GUIDE SERVICE TIPS ZF Industries DIAGNOSIS AND TESTING Inspection and Verification.

Download

Wednesday, May 12, 2010

Ford Focus Zetec Complete Report Manual

In fact the Ford Focus makes you question what is a small car these days? In a practical departure from most new cars the glove box can take a full size street directory and have room left over. This makes up for the narrow front door pockets and small centre armrest compartment. While there aren’t any rear door pockets, small moulded trays next to the seat look after your knick knacks. Large and heavy, the rear hatch opens quite high, in fact you need to be a bit careful with it. Once open it can require a bit of muscle to get back down.

Download

Tuesday, May 11, 2010

2002 Ford E450 Cutaway Owners Manual

Remove the attached body, if applicable. Remember to disconnect all electrical connections to the body, and fuel filler tube, before removing the body. The installation can also be completed using a lift to raise the vehicle. If using a lift, chassis body removal may not be necessary but removal of rear wheels will aid in installation.

Download

Monday, May 10, 2010

Ford ACCEL Digital Fuel Injection Engine Management System Installation Manual

ACCEL recommends using a 180 degree thermostat in most applications. Place your thermostat and gasket onto your manifold, put your thermostat housing onto the manifold and bolt in place. When installing your fuel injectors, be careful not to cut the O-Rings. A small amount of oil on each O-Ring will aid in the assembly. Please reference a service manual for proper torque sequence and vacuum line routing.

Download

Saturday, July 12, 2008

Ford Car Mobile Radio Installation Guidelines

Ford Motor Company vehicles are designed and tested for safe operation with properly installed and properly used land mobile/amateur radio communication equipment with up to 100 Watt transmitter power.
Special design considerations are incorporated into all Ford vehicle electronic systems to provide immunity to radio frequency signals. To maintain compatibility with vehicle electronic systems, mobile two-wayradio and telephone equipment must be installed properly by trained personnel, observing these general guidelines:

- Power connections should be made directly to the battery and fused as close to the battery as possible. Avoid using cigar lighter or “Power Point” receptacles as power sources for radio communication equipment.
- Antennas for two-way radios should be mounted on the roof or the rear area of the vehicle. Care should be used in mounting antennas with magnet bases, since magnets may affect the accuracy or operation of the compass on vehicles, if so equipped.
- The antenna cable should be high quality, fully shielded coaxial cable, and kept as short as practical. Avoid routing the antenna cable in parallel with vehicle wiring over long distances.
- Carefully match the antenna and cable to the radio to achieve a low Standing Wave Ratio (SWR) and to avoid RF currents on the antenna cable shield.

Download

1997 Ford F 150 4.6 97 Expedition Heater Core Replacement Instructions

Shopping list from FORD dealer, $15.00 for 2 sets of heater hose o-rings and snap clips, $40.00 heater core, (cheaper at the dealer but no warrantee, aftermarket parts store model preferred by many @ $55) insulated foam tape to wrap new core with (parts dept just gave me what I needed), and a gallon of anti freeze.

1. Tying off the antenna cable to a old shoelace was a great little trick that made the reassembly a snap, allowed pulling antenna cable back out of the hole real easy. I used elect tape too, didn’t want "ANY" surprises later!
2. Get the heater hose removal tool from a mechanic willing to loan it out to you. I was surprised at the helping hand the dealer mechs were. The tool took a few minutes to figure out. Took a second trip back to the Ford dealer for replacement o-rings and clips. save time, buy these first cause you'll break the originals, if you dont, change em anyway, your in this deep!! 2-A Another method without using the tool is just cutting off the inlet and outlet pipes from the heater core with a saws-all and pulling the hose/pipe out from the engine compartment side. This is done after the H-Core plenum is removed. I got so frustrated without the special tool I nearly did this too!!
3. Leave all the steering column and large bulkhead elect plugs attached, I unhooked these before the Ford mechanic advised me not to mess with them.
4. Try to follow in reverse the "dash removal instructions" during reassembly so you dont have any "do overs" when you cant get a screw to line up properly. (Don’t ask how I now this)
5. Get a large box for all the trim parts.
6. Updated tip To help to figure out where all the screws go I am recommending an idea from a user of this heater doc who offered this tip. I wish I had used this method myself, had 3 left over, no rattles. Tip: if you have a helper, have them read the steps aloud while you perform them and also have them put the screws removed in baggies labeled with the corresponding number of the step.
7. I removed the big elect housing located right over the heater core housing to aide in getting the cover reinstalled, it was in the way when I was reinstalling the plenum cover, 2 screws, no big deal.

Download

Ford Mustang Wiring Diagram for 1987-1993 Instrument Cluster

If you are attempting to install a 1990-1993 steering wheel in a 1987-1989 car, then the steering column must also be changed. All
connections will hook up in the steering column except for the harness from the steering wheel, which provides the horn and cruise control signal. The windshield wipers will not work if the 1990-1993 switch is used on the 1987-1989 harness. Testing with a multimeter will show you the wires that Ford chose to move when the design of the switch changes. All controls have the same wiring except the windshield wipers. After the correct wires are determined, it is an easy task to remove the wires from the plug by pressing down on the tab on the front of the plug and sliding the wire out the back. Then, the wire can be inserted into the previously unused connection hole on the plug.

This process if much easier if you have an old harness from a 1990-1993 that comes out of the instrument cluster. The wires need to be as long as possible (6-8 inches), and they can be successfully wire tapped and soldered to the factory 1987-1989 harness.

Download

2005 Ford Mustang GT Roushcharger Kit Installation Instructions

Application: 2005 Ford Mustang GT 4.6L 3 Valve with Manual Transmissions Only. Before installing your Roush Performance Products, please read the installation manual and verify that all items are present. Premium fuel (91 octane minimum) is required to prevent “spark-knock” or detonation under certain operating conditions.

There is a great deal of misinformation about the function of Roushcharger bypass systems. The Roushcharger is a positive-displacement pump; that is, so long as it is rotating, it is always pumping air. During low demand or high vacuum operation (idles, decelerations, and light throttle cruise), the pumping action is undesirable as it creates unwanted heat and noise. The bypass circuit, when open, prevents any pressure buildup across the Roushcharger and allows air to circulate through the rotors, allowing the Roushcharger to “idle” freely during these conditions. This results in reduced noise, and by reducing heat buildup in the intake, significantly improves street and strip performance. As throttle demand increases, the bypass circuit is closed, resulting in full performance from the Roushcharger. The bypass circuit is never used to limit or control boost during full-throttle operation and defeating or altering the bypass function will not result in improved performance in any condition, and will result in poor drivability.

Download