MANUAL AIR CONDITIONER: Heater Control Name Sheet No. 2 Air Conditioner Amplifier Assy Integration Control & Panel Bulb x5 Heater Control Housing Sub−assy Heater Control Housing Heater Blower Switch Radio Bracket No. 1 Heater Control Name Sheet No. 1 Control Knob Sub−assy AUTO AIR CONDITIONER: Heater Control Housing Sub−assy Control Knob Sub−assy Integration Control & Panel Bulb x9 Glove Compartment Door Assy ECM Blower Assy Air Duct No. 2 9.8 (100, 87 in.⋅lbf) Recirculation Damper Servo Sub−assy Filter Cover Cooling Unit Motor Sub−assy w/ fan.
Front Pillar Garnish LH Front Pillar Garnish RH H Instrument Panel Finish Panel Lower No.2 20 (205, 15) Radio Bracket No.1&No.2 With Combination Meter Assy Radio Receiver Instrument Cluster Instrument Cluster Finish Finish Panel Garnish Panel Sub−assy Center Grove Compartment Steering Column Door Assy Cover UPR Instrument Cluster Cowl Side Trim Windshield Wiper Finish Panel Assy Sub−assy RH Switch Assy
Source
Showing posts with label instrument cluster. Show all posts
Showing posts with label instrument cluster. Show all posts
Friday, May 21, 2010
Wednesday, July 16, 2008
BMW SRI Manual Reset 2001
On 2001 vehicles without the diagnostic connector in the engine compartment, the use of the SIA reset tool is not possible. The service indicator may be reset using the reset mode in the instrument cluster.
Reset procedure for high and low clusters with SIA III using the Reset Mode:
• Ignition key must be “off”
• Press and hold the trip odometer reset button in the instrument cluster (left button), and turn the ignition key to the first position.
• Keep the button pressed for approximately 5 seconds until one of the following words appear in the display: “OIL SERVICE, or “INSPECTION”, with “RESET”. The service due is shown with “reset” if the coded minimum consumption limit has been reached and resetting is possible. If “reset” is not shown, the minimum limit has not been reached and resetting is not possible.
• Press and hold the reset button again until the word “RESET” begins to flash.
Download
Reset procedure for high and low clusters with SIA III using the Reset Mode:
• Ignition key must be “off”
• Press and hold the trip odometer reset button in the instrument cluster (left button), and turn the ignition key to the first position.
• Keep the button pressed for approximately 5 seconds until one of the following words appear in the display: “OIL SERVICE, or “INSPECTION”, with “RESET”. The service due is shown with “reset” if the coded minimum consumption limit has been reached and resetting is possible. If “reset” is not shown, the minimum limit has not been reached and resetting is not possible.
• Press and hold the reset button again until the word “RESET” begins to flash.
Download
Saturday, July 12, 2008
Ford Mustang Wiring Diagram for 1987-1993 Instrument Cluster
If you are attempting to install a 1990-1993 steering wheel in a 1987-1989 car, then the steering column must also be changed. All
connections will hook up in the steering column except for the harness from the steering wheel, which provides the horn and cruise control signal. The windshield wipers will not work if the 1990-1993 switch is used on the 1987-1989 harness. Testing with a multimeter will show you the wires that Ford chose to move when the design of the switch changes. All controls have the same wiring except the windshield wipers. After the correct wires are determined, it is an easy task to remove the wires from the plug by pressing down on the tab on the front of the plug and sliding the wire out the back. Then, the wire can be inserted into the previously unused connection hole on the plug.
This process if much easier if you have an old harness from a 1990-1993 that comes out of the instrument cluster. The wires need to be as long as possible (6-8 inches), and they can be successfully wire tapped and soldered to the factory 1987-1989 harness.
Download
connections will hook up in the steering column except for the harness from the steering wheel, which provides the horn and cruise control signal. The windshield wipers will not work if the 1990-1993 switch is used on the 1987-1989 harness. Testing with a multimeter will show you the wires that Ford chose to move when the design of the switch changes. All controls have the same wiring except the windshield wipers. After the correct wires are determined, it is an easy task to remove the wires from the plug by pressing down on the tab on the front of the plug and sliding the wire out the back. Then, the wire can be inserted into the previously unused connection hole on the plug.
This process if much easier if you have an old harness from a 1990-1993 that comes out of the instrument cluster. The wires need to be as long as possible (6-8 inches), and they can be successfully wire tapped and soldered to the factory 1987-1989 harness.
Download
Subscribe to:
Posts (Atom)