Honda S2000 Seat Belt Lock Remote Installation

This product is to be used ONLY on the Honda S2000 and is intended to provide increased driver support when using the stock lap belt and shoulder harness. It is NOT to be used as a replacement for competition belts or at any event where 4 or 5-point restraint systems are required. This product uses an electro-magnet to activate the factory inertia-sensing mechanism built into the seat belt assembly. It does not alter the factory restraint system in any way and has no effect on the seat belt retractors or air bag system. It simply activates the “tilt” mechanism built into the seat belt, the one that normally kicks in only when you corner or brake very hard. Modifry’s Seat Belt Lock is relatively easy to install and can be quickly removed, leaving no trace it was there.

Installation
1. Prepare - Empty the trunk of anything breakable or that might get in the way of sitting in the trunk (really). Remove the spare tire access panel and the spare tire. Then slide and tilt the passenger seat as far forward as it will go. Note – I use the abbreviation “SBL” for the Seat Belt Lock, which is the black bracket with the electro-magnet attached.
2. Remove the access panel behind the passenger seat. Unsnap the screw covers on the two plastic hooks and then remove the screws. Carefully pull the panel out, starting at the bottom and working around the outer edge to release the clips that hold it in place.
3. Locate the accessory power socket wire harness. This wire loom goes under the glove box on the right. Pry apart the plastic (it’s split down the middle) and pull the black and white/red wires out in preparation for attaching the T-taps. If the two wires are not black and white/red STOP, you have the wrong wire loom.

Download

2001 Highlander Heater & Air Conditioner Components Repair Manual

MANUAL AIR CONDITIONER: Heater Control Name Sheet No. 2 Air Conditioner Amplifier Assy Integration Control & Panel Bulb x5 Heater Control Housing Sub−assy Heater Control Housing Heater Blower Switch Radio Bracket No. 1 Heater Control Name Sheet No. 1 Control Knob Sub−assy AUTO AIR CONDITIONER: Heater Control Housing Sub−assy Control Knob Sub−assy Integration Control & Panel Bulb x9 Glove Compartment Door Assy ECM Blower Assy Air Duct No. 2 9.8 (100, 87 in.⋅lbf) Recirculation Damper Servo Sub−assy Filter Cover Cooling Unit Motor Sub−assy w/ fan.
Front Pillar Garnish LH Front Pillar Garnish RH H Instrument Panel Finish Panel Lower No.2 20 (205, 15) Radio Bracket No.1&No.2 With Combination Meter Assy Radio Receiver Instrument Cluster Instrument Cluster Finish Finish Panel Garnish Panel Sub−assy Center Grove Compartment Steering Column Door Assy Cover UPR Instrument Cluster Cowl Side Trim Windshield Wiper Finish Panel Assy Sub−assy RH Switch Assy

Source

1994-1998 Honda Accord Radio Replacement Installation

Tools Needed To Complete This Install Hand tools needed Accessory tools needed to test and to remove radio wire the new radio PLUS: Wire ties or electrical tape: to neatly bundle and organize your wires for a professional appearance. TOOL TIPS: Small Battery: use a battery to test speaker wires. Touching the (+) positive and (-) negative baterry leads to a pair of speaker will cause the speaker to make a “Pop” sound indicating that pair of wires goes to that speaker. Voltage Meter: Always check +12 Volt power wires for voltage before making wire connections. These wires will fluctuate between 10 and 14 Volts. Solder Iron or Crimp Tool: make wire to wire connections using either a solder iron and electrical tape, OR plastic crimp terminals found at most hardware or auto parts stores.
STEP 1: The center dash console must be loosened and pulled away in order to gain access to screws securing the plastic dash panel surrounding the radio. Open the center console glove box. At the very bottom is a plastic panel that covers hidden screws. With your fingers or a flat head screwdriver, lift up and remove the plastic panel. Once the panel is removed, locate and remove two (2) phillips screws.
STEP 2: Lift open the drink tray door. Pull the drink tray up and pull it out of the center console.
STEP 3: Once the drink tray is removed, locate and Once the three screws have been removed, Hidden under the center console are two (2) remove three (3) phillips screws. the center console can be pull back, away phillips screws that secure the plastic trim from the gear shift console. panel that surrounds the gear shift. Remove (2) screws will be at the bottom of the panel, both screws. and (1) will be at the front left corner near the You only need to pull the center console back top of the opening. 2-3 inches as seen in the photo above.

Source

1996 Volkswagen Golf Fuses & Circuit Breakers

The fuse panel is located under the left side of the dash board by the driver's knee on the Cabriolet, Fox, Jetta, Rabbit and Pickup. On the Golf and GTI models the panel is located by the driver's right knee, under the dash panel.
NOTE: On all models, fuse specifications are listed on inside of panel cover.
WARNING: Always disconnect battery ground cable before servicing "high-current fuses. It is recommended that "high-current" fuses be replaced by a qualified technician.

RADIATOR CAP
CAUTION: Always disconnect the fan motor when working near the radiator fan. The fan is temperature controlled and could start at any time even when the ignition key is in the OFF position. DO NOT loosen or remove radiator cap when cooling system is hot.

REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off all lights and accessories to avoid damaging the electrical system. Be sure to use fuse with the correct indicated amperage rating. The use of an incorrect amperage rating fuse may result in a dangerous electrical system overload.

BATTERY WARNING
CAUTION: When battery is disconnected, vehicles equipped with computers may lose memory data. When battery power is restored, driveability problems may exist on some vehicles. These vehicles may require a relearn procedure. See COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION section.

Download

Volkswagen Wiring Diagram User Manual

Free Download User Manual Volkswagen Wiring Diagram. Explanation: 1. Relay location number, indicates location on relay panel. 2. Arrow, indicates wiring circuit is continued on the previous and/or next page. 3. Connection designation, relay control module on relay panel. Shows the individual terminals in a multi-point connector. 4. Diagram of threaded pin on relay panel, white circle shows a detachable connection. 5. Fuse designation. 6. Reference of wire continuation (current track number).

Download

Kawasaki Teryx 750 ATV Clutch Kit Instructions

The instructions we provide are guidelines only and will not thoroughly explain how to set up a racing vehicle. Claims of performance gains, durability, etc. are based on the experience of TEAM Industries and others and do not constitute a guarantee of similar performance in every application. We believe that the contents and specifications within this set of instructions are correct. We assume no liability for any errors in model applications. We reserve the right to change specifications, product descriptions, product quality and application at any time without notice.

Make sure your current clutches are free of fatigue, cracks, wear, etc. TEAM clutch components are produced with high quality materials and a controlled procedure. Never alter TEAM Industries clutch components.

1. Remove both seats from the vehicle. Next, remove the passenger side lower body panel. There is a mixture of Philips head screws and also plastic push pin fasteners that have to be removed.
2. With the side panel off, the next item to remove is the plastic housing over the engine. These are all “push in” style plastic clips that hold it in place. Once all the pins are out, you can slide the housing off and set it aside.
3. Now the lower long plastic panel under the seat has to be removed (again mainly plastic push clips to remove). Once they are all out, carefully remove and set aside.
4. Next, remove the fuel tank. Remove the two lines on the top of the tank. There are two straps that hold the tank in place. Remove the bolt from each strap, remove the straps, and lift the fuel tank out.
5. Now the bracket that holds the fuel pump on has to be removed. There are two bolts here to take out. Once this is done, mark the two wires to the coil and disconnect them. Set the bracket out of the way.

Download

Powerwave Series Technical Manual

Before installing this version of upload/download software, please remove any existing PW8 or PW16 software first.
This is done by going to “Control Panel” then “Add/Remove Programs”. Next, select the “8 (or 16) zone panel upload download” option in the window then select “Add/Remove”. Once the old program has been removed you may proceed to install the new software. (NOTE: if you remove the old program as described above, all of your customer database files will be retained in the “Upload Download” folder, see below for the full directory tree).

To install the software, insert the disk labeled Disk 1 of 2 into the floppy drive. Next, select “Run” from the start menu.
Then type in; A:\setup.exe(use B:\setup.exe if using the B drive). The program will automatically install itself. When the installation process asks for Disk 2, remove Disk 1 from the floppy drive replacing it with disk 2 of 2 then press “enter”. When finished, select the “restart the computer” option so that the installation process can be completed.
The software will automatically create a new folder called “8 Zone Panel Upload Download” or “16 Zone Panel Upload Download” and install itself in the following area on your com- puters “C:” drive;

Download