Quest van Navigation System OM navi USA English nna 05 05 04 debbie MEMO 12 8 Information on map data discs 13 Troubleshooting guide Customer assistance 13 2 Basic operations 13 3 Vehicle icon 13 4 Map DVD ROM 13 6 Destination waypoints or menu contents cannot be chosen or set 13 7 Voice guidance 13 8 Route calculation.
The brightness adjustment is at the lowest setting No map DVD ROM is inserted or it is inserted upside down The map display mode is switched off Remedy Adjust the settings to make the display brighter Insert the DVD ROM correctly Press the MAP button No voice guide is available or The volume is not high enough The screen is too dim The movement is slow There are a few darker or brighter dots in the display The volume is not set correctly or turned off Adjust the volume correctly The temperature in the vehicle is low This is inherent to displays This condition is a characteristic of liquid crystal displays Wait for the temperature in the vehicle to rise This condition is not abnormal Stored location in the address book and other memory functions may be lost if the vehicle s battery is disconnected or becomes discharged for a long time If this should occur service the vehicle s battery as necessary and re enter the address book information Troubleshooting guide 13 3 REVIEW COPY 2004 Quest van Navigation System OM navi USA English nna 05 05 04 debbie VEHICLE ICON Symptom The location names differ between Planview and Birdview Possible cause This is because the displayed information is reduced so that the screen does not become too crowded There is also a chance that names of roads or locations will be displayed twice.
Download
Showing posts with label nissan quest. Show all posts
Showing posts with label nissan quest. Show all posts
Monday, May 10, 2010
Sunday, May 9, 2010
Nissan Quest 2002 Owners Manual
To determine if you have one of these systems depress the button on the HomeLink Universal Transceiver that you have just programmed If the LED on the HomeLink Universal Transceiver flashes rapidly for 1 to 2 seconds then remains on your garage door opener has a rolling code system To operate your rolling code garage door opener from your HomeLink Universal Transceiver follow these steps.
1 Program your hand held transmitter to the HomeLink Universal Transceiver by following the procedures outlined previously if not yet programmed 2 Program your garage door opener receiver to recognize the HomeLink Uni versal Transceiver The HomeLink Universal Transceiver follows the same procedure to train to the receiver as your hand held transmitter did when it was first installed a Remove the cover panel from your garage door opener receiver The receiver should be located by the garage door opener motor b Locate the training button on the garage door opener receiver The exact location and color of the button may vary by garage door opener brand If you have difficulty locating the training button reference your garage door opener manual If you have difficulty programming your garage door opener equipped with a rolling code system to recognize the HomeLink Universal Transceiver with the Rolling Code feature call NISSAN Consumer Affairs Department c Press the training button on the garage door opener receiver for 1 to 2 seconds AIC1070 CLEARING THE PROGRAMMED INFORMATION Should you sell your vehicle be sure to clear the channels of the HomeLink Universal Transceiver To clear the channels simultaneously hold down the outside two buttons 1 3 until the red indicator light begins to flash rapidly approximately 20 seconds This will clear all three buttons Individual buttons cannot be cleared but can be reprogrammed at any time by following the programming procedures described previously 2 38 Instruments and controls d Return to the HomeLink Universal Transceiver in the vehicle and depress the programmed HomeLink button for the duration of the fast blink on the HomeLink Universal Transceiver 1 to 2 seconds Release the button and repress to confirm that the system has trained e Your garage door opener should now recognize your HomeLink Universal Transceiver You may use either your HomeLink Universal Transceiver or your original hand held transmitter to open your garage door FFC Notice This device complies with FCC rules part 15 Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference that may be received including interference that may cause undesired operation The transmitter has been tested and complies with FCC and DOC MDC rules Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the device DOC ISTC 1763K1313 FCC I D CB2V67690 IF YOUR VEHICLE IS EVER STOLEN If your vehicle has been stolen you should change the codes of any device that was programmed into the HomeLink Universal Transceiver as soon as possible Consult the owners manual of each device or call the manufacturer or dealer of those devices When your vehicle is recovered you will have to reprogram the HomeLink Universal Transceiver with your new transmitter information Instruments and controls 2 39 MEMO 2 40 Instruments and controls.
Download
1 Program your hand held transmitter to the HomeLink Universal Transceiver by following the procedures outlined previously if not yet programmed 2 Program your garage door opener receiver to recognize the HomeLink Uni versal Transceiver The HomeLink Universal Transceiver follows the same procedure to train to the receiver as your hand held transmitter did when it was first installed a Remove the cover panel from your garage door opener receiver The receiver should be located by the garage door opener motor b Locate the training button on the garage door opener receiver The exact location and color of the button may vary by garage door opener brand If you have difficulty locating the training button reference your garage door opener manual If you have difficulty programming your garage door opener equipped with a rolling code system to recognize the HomeLink Universal Transceiver with the Rolling Code feature call NISSAN Consumer Affairs Department c Press the training button on the garage door opener receiver for 1 to 2 seconds AIC1070 CLEARING THE PROGRAMMED INFORMATION Should you sell your vehicle be sure to clear the channels of the HomeLink Universal Transceiver To clear the channels simultaneously hold down the outside two buttons 1 3 until the red indicator light begins to flash rapidly approximately 20 seconds This will clear all three buttons Individual buttons cannot be cleared but can be reprogrammed at any time by following the programming procedures described previously 2 38 Instruments and controls d Return to the HomeLink Universal Transceiver in the vehicle and depress the programmed HomeLink button for the duration of the fast blink on the HomeLink Universal Transceiver 1 to 2 seconds Release the button and repress to confirm that the system has trained e Your garage door opener should now recognize your HomeLink Universal Transceiver You may use either your HomeLink Universal Transceiver or your original hand held transmitter to open your garage door FFC Notice This device complies with FCC rules part 15 Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference that may be received including interference that may cause undesired operation The transmitter has been tested and complies with FCC and DOC MDC rules Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the device DOC ISTC 1763K1313 FCC I D CB2V67690 IF YOUR VEHICLE IS EVER STOLEN If your vehicle has been stolen you should change the codes of any device that was programmed into the HomeLink Universal Transceiver as soon as possible Consult the owners manual of each device or call the manufacturer or dealer of those devices When your vehicle is recovered you will have to reprogram the HomeLink Universal Transceiver with your new transmitter information Instruments and controls 2 39 MEMO 2 40 Instruments and controls.
Download
Thursday, May 6, 2010
1999 Nissan Quest Owners Manual.pdf
Turn the ignition key to the OFF position and secure the steering wheel in a straight ahead position with a rope or similar device Never place the ignition key in the LOCK position This will result in damage to the steering lock mechanism Move the gearshift lever to the N Neutral position When towing with the rear wheels on the ground release the parking brake.
Attach safety chains for all towing 6 12 In case of emergency ACE1029 NISSAN recommends that your vehicle be towed with the driving front wheels off the ground as illustrated Speed Below 60 MPH 97 km h Distance Less than 500 miles 800 km In case of emergency 6 13 CAUTION Never tow the vehicle with the rear wheels raised with the front wheels on the ground as this may cause serious and expensive damage to the transmission If it is necessary to tow the vehicle with the rear wheels raised always use towing dollies under the front wheels If you have to tow the vehicle with four wheels on ground observe the following restricted towing speeds and distances Speed Below 30 MPH 50 km h Distance Less than 40 miles 65 km Never tow the vehicle from the rear i e backward with four wheels on the ground as this may cause serious and expensive damage to the transmission Do not tow with a sling type truck either from the front or the rear It may cause body damage Never utilize the rear tie down brackets or slots to tow another vehicle as this may cause body damage VEHICLE RECOVERY freeing a stuck vehicle Tow chains or cables must only be attached to the main structual members of the vehicle Pulling devices should be routed so they do not touch any part of the suspension steering brake or cooling systems Always pull the cable straight out from the front or rear of the vehicle Never pull the vehicle at an angle Pulling devices such as ropes or canvas straps are not recommended for use in vehicle towing or recovery Stand clear of a stuck vehicle WARNING Do not spin your tires at high speed This could cause them to explode and result in serious injury Parts of your vehicle could also overheat and be damaged 6 14 In case of emergency 7 Appearance and care Cleaning exterior and interior 7 2 Corrosion protection 7 4 CLEANING EXTERIOR AND INTERIOR when dust or mud builds up on the surface Whenever possible store or park your vehicle inside a garage or in a covered area When it is necessary to park outside park in a shady area or protect the vehicle with a body cover Be careful not to scratch the paint surface when putting on or removing a body cover Avoid using tight napped or rough cloths such as washing mitts Care must be taken when removing caked on dirt or other foreign substances so the paint surface is not scratched or damaged Rinse the vehicle thoroughly with plenty of clean water Inside flanges seams and folds on the doors hatches and hood are particularly vulnerable to the effects of road salt Therefore these areas must be regularly cleaned Take care that the drain holes in the lower edge of the door are open.
Download
Attach safety chains for all towing 6 12 In case of emergency ACE1029 NISSAN recommends that your vehicle be towed with the driving front wheels off the ground as illustrated Speed Below 60 MPH 97 km h Distance Less than 500 miles 800 km In case of emergency 6 13 CAUTION Never tow the vehicle with the rear wheels raised with the front wheels on the ground as this may cause serious and expensive damage to the transmission If it is necessary to tow the vehicle with the rear wheels raised always use towing dollies under the front wheels If you have to tow the vehicle with four wheels on ground observe the following restricted towing speeds and distances Speed Below 30 MPH 50 km h Distance Less than 40 miles 65 km Never tow the vehicle from the rear i e backward with four wheels on the ground as this may cause serious and expensive damage to the transmission Do not tow with a sling type truck either from the front or the rear It may cause body damage Never utilize the rear tie down brackets or slots to tow another vehicle as this may cause body damage VEHICLE RECOVERY freeing a stuck vehicle Tow chains or cables must only be attached to the main structual members of the vehicle Pulling devices should be routed so they do not touch any part of the suspension steering brake or cooling systems Always pull the cable straight out from the front or rear of the vehicle Never pull the vehicle at an angle Pulling devices such as ropes or canvas straps are not recommended for use in vehicle towing or recovery Stand clear of a stuck vehicle WARNING Do not spin your tires at high speed This could cause them to explode and result in serious injury Parts of your vehicle could also overheat and be damaged 6 14 In case of emergency 7 Appearance and care Cleaning exterior and interior 7 2 Corrosion protection 7 4 CLEANING EXTERIOR AND INTERIOR when dust or mud builds up on the surface Whenever possible store or park your vehicle inside a garage or in a covered area When it is necessary to park outside park in a shady area or protect the vehicle with a body cover Be careful not to scratch the paint surface when putting on or removing a body cover Avoid using tight napped or rough cloths such as washing mitts Care must be taken when removing caked on dirt or other foreign substances so the paint surface is not scratched or damaged Rinse the vehicle thoroughly with plenty of clean water Inside flanges seams and folds on the doors hatches and hood are particularly vulnerable to the effects of road salt Therefore these areas must be regularly cleaned Take care that the drain holes in the lower edge of the door are open.
Download
Wednesday, May 5, 2010
1998 Nissan Quest Owners Manual Download
If you detect any unusual sounds vibrations or smells be sure to check for the cause or have an authorized NISSAN dealer do it promptly In addition you should notify an authorized NISSAN dealer if you think repairs are required When performing any checks or maintenance work closely observe the precautions in the Do it yourself section of this manual.
Additional information on the following items with an can be found in the Do it yourself section of this manual General maintenance General maintenance includes those items which should be checked during normal day to day operation of the vehicle They are essential if your vehicle is to continue to operate properly It is your responsibility to perform these maintenance procedures regularly as prescribed These checks or inspections can be done by yourself a qualified technician or if you prefer an authorized NISSAN dealer OUTSIDE THE VEHICLE The maintenance items listed here should be performed from time to time unless otherwise specified Tires Check the pressure with a gauge periodically when at a service station including the spare and adjust to the specified pressure if necessary Check carefully for damage cuts or excessive wear Wheel nuts When checking the tires 9 2 Maintenance make sure no wheel nuts are missing and check for any loose wheel nuts Tighten if necessary Tire rotation Tires should be rotated every 7 500 miles 12 000 km Wheel alignment and balance If the vehicle should pull to either side while driving on a straight and level road or if you detect uneven or abnormal tire wear there may be a need for a wheel alignment If the steering wheel or seat vibrates at normal highway speeds wheel balancing may be needed Windshield wiper blades Check for cracks or wear if they do not wipe properly Doors and hood Check that all doors and the hood operate properly Also ensure that all latches lock securely Lubricate hinges latches rollers and links if necessary Make sure the secondary latch keeps the hood from opening when the primary latch is released When driving in areas using road salt or other corrosive materials check lubrication frequently INSIDE THE VEHICLE The maintenance items listed here should be checked on a regular basis such as when performing periodic maintenance cleaning the vehicle etc Additional information on the following items with an is found in the Do ityourself section of this manual Lights Make sure the headlights stop lights tail lights turn signal lights and other lights are all operating properly and installed securely Also check headlight aim Warning lights and buzzers chimes Make sure all warning lights and buzzers chimes are operating properly Windshield wiper and washer Check that the wipers and washer operate properly and that the wipers do not streak Windshield defroster
Download
Additional information on the following items with an can be found in the Do it yourself section of this manual General maintenance General maintenance includes those items which should be checked during normal day to day operation of the vehicle They are essential if your vehicle is to continue to operate properly It is your responsibility to perform these maintenance procedures regularly as prescribed These checks or inspections can be done by yourself a qualified technician or if you prefer an authorized NISSAN dealer OUTSIDE THE VEHICLE The maintenance items listed here should be performed from time to time unless otherwise specified Tires Check the pressure with a gauge periodically when at a service station including the spare and adjust to the specified pressure if necessary Check carefully for damage cuts or excessive wear Wheel nuts When checking the tires 9 2 Maintenance make sure no wheel nuts are missing and check for any loose wheel nuts Tighten if necessary Tire rotation Tires should be rotated every 7 500 miles 12 000 km Wheel alignment and balance If the vehicle should pull to either side while driving on a straight and level road or if you detect uneven or abnormal tire wear there may be a need for a wheel alignment If the steering wheel or seat vibrates at normal highway speeds wheel balancing may be needed Windshield wiper blades Check for cracks or wear if they do not wipe properly Doors and hood Check that all doors and the hood operate properly Also ensure that all latches lock securely Lubricate hinges latches rollers and links if necessary Make sure the secondary latch keeps the hood from opening when the primary latch is released When driving in areas using road salt or other corrosive materials check lubrication frequently INSIDE THE VEHICLE The maintenance items listed here should be checked on a regular basis such as when performing periodic maintenance cleaning the vehicle etc Additional information on the following items with an is found in the Do ityourself section of this manual Lights Make sure the headlights stop lights tail lights turn signal lights and other lights are all operating properly and installed securely Also check headlight aim Warning lights and buzzers chimes Make sure all warning lights and buzzers chimes are operating properly Windshield wiper and washer Check that the wipers and washer operate properly and that the wipers do not streak Windshield defroster
Download
Tuesday, May 4, 2010
1996 Nissan Quest Owners Manual
The gauge needle is designed to remain in approximately the same position even when the ignition key is turned OFF Refill the fuel tank before the gauge registers at E empty 1 5 WARNING INDICATOR LIGHTS AND CHIMES AIC0583 Checking bulbs Apply the parking brake fasten seat belts and turn the ignition key to ON without starting the engine The following lights come on and stay on until the engine is started indicate a burned out bulb or an open circuit in the electrical system.
Have the system repaired promptly Engine oil pressure warning light This light warns of low engine oil pressure If the light flickers or comes on during normal driving pull off the road in a safe area stop the engine immediately and call a NISSAN dealer or other authorized repair shop Running the engine with the oil pressure warning light on could cause serious damage to the engine 1 6 The oil pressure warning light is not designed to indicate a low oil level Use the dipstick to check the oil level See Engine oil in the Do it yourself operations section Charge warning light If the light comes on while the engine is running it may indicate something wrong with the charging system Turn the engine off and check the generator belt If the belt is loose broken missing or if the light remains on see your NISSAN dealer immediately The following lights come on briefly and then go off ABS or If any light fails to come on it may CAUTION Do not continue driving if the belt is loose broken or missing Supplemental air bag warning light When the ignition key is in the ON or START position the supplemental air bag warning light illuminates for about 7 seconds and then turns off This means the Air Bag Supplemental Restraint System is operational If any of the following conditions occur the supplemental air bag system needs servicing and your vehicle should be taken to your nearest authorized NISSAN dealer as soon as practical 1 The supplemental air bag warning light does not come on for 7 seconds and then go off as described above 2 The supplemental air bag warning light flashes intermittently or remains on 3 The supplemental air bag warning light does not come on at all Unless checked and repaired the Air Bag Supplemental Restraint System may not function properly For additional details see Supplemental restraint system in the Predriving checks and adjustments section 1 7 Low washer fluid warning light This light comes on when the washer reservoir fluid is at a low level Add washer fluid as necessary See the Do it yourself operations section
Download
Have the system repaired promptly Engine oil pressure warning light This light warns of low engine oil pressure If the light flickers or comes on during normal driving pull off the road in a safe area stop the engine immediately and call a NISSAN dealer or other authorized repair shop Running the engine with the oil pressure warning light on could cause serious damage to the engine 1 6 The oil pressure warning light is not designed to indicate a low oil level Use the dipstick to check the oil level See Engine oil in the Do it yourself operations section Charge warning light If the light comes on while the engine is running it may indicate something wrong with the charging system Turn the engine off and check the generator belt If the belt is loose broken missing or if the light remains on see your NISSAN dealer immediately The following lights come on briefly and then go off ABS or If any light fails to come on it may CAUTION Do not continue driving if the belt is loose broken or missing Supplemental air bag warning light When the ignition key is in the ON or START position the supplemental air bag warning light illuminates for about 7 seconds and then turns off This means the Air Bag Supplemental Restraint System is operational If any of the following conditions occur the supplemental air bag system needs servicing and your vehicle should be taken to your nearest authorized NISSAN dealer as soon as practical 1 The supplemental air bag warning light does not come on for 7 seconds and then go off as described above 2 The supplemental air bag warning light flashes intermittently or remains on 3 The supplemental air bag warning light does not come on at all Unless checked and repaired the Air Bag Supplemental Restraint System may not function properly For additional details see Supplemental restraint system in the Predriving checks and adjustments section 1 7 Low washer fluid warning light This light comes on when the washer reservoir fluid is at a low level Add washer fluid as necessary See the Do it yourself operations section
Download
Monday, May 3, 2010
2007 Nissan Quest Quick Reference Guide
hen the vehicle reaches the speed you desire release the switch To reset at a slower cruising speed push and hold the COAST SET switch Release the switch when the vehicle slows to the desired speed To resume a preset speed push and release the ACCEL RES switch The vehicle returns to the last set cruising speed when the vehicle speed is over 24 MPH 38 km h.
To cancel cruise control push the CANCEL switch or tap the brake pedal The SET indicator light in the instrument panel will go out To turn off cruise control push the ON OFF switch Both the CRUISE indicator light and the SET indicator light in the instrument panel will go out Use the dials 03 at the side of the driver s seat to adjust the angle and height of the seat cushion With power seats if so equipped Move the control 04 forward or backward to adjust the seat cushion forward or backward Pull up to raise the driver s seat cushion press down to lower the cushion 04 Push the switch 05 forward to move the seatback forward press it back to move the seatback backward Your driver s seat has a lumbar support adjust it by moving the lever 06 forward or backward 12 02 04 05 01 14 AUTOMATIc clIMATE cONTROl if so equipped 01 Press the REAR CTRL button to transfer rear climate functions to the rear passengers 05 06 04 06 03 AUTO BUTTON Press the AUTO button 01 Turn the driver s side temperature control dial 02 to the desired temperature This will allow the fan speed air flow distribution and temperature to be automatically maintained Press the DUAL 03 button to turn the passenger s side temperature controls on or off This will allow the passenger s side temperature to be adjusted independently from driver s side control When AUTO is pressed AUTO will be displayed When DUAL is pressed DUAL will be displayed DRIVER S SIDE TEMPERATURE CONTROL DIAL Turn the driver s temperature control dial left for cold air or right for hot air PASSENGER S SIDE TEMPERATURE CONTROL DIAL Turn the passenger s temperature control dial left for cold air or right for hot air AIR FLOW MODE BUTTONS Press to select the following air flow outlets Air flows from the center and side vents Air flows from the center side and foot vents Air flows mainly from the foot vents Air flows from the defroster and foot vents Air flows mainly from the defroster vents FAN SPEED CONTROL BUTTONS Press slower or faster button repeatedly to manually control fan speed Press AUTO to automatically control fan speed Press OFF to cancel fan speed operation DEFROSTING DEFOGGING FRONT AND SIDE WINDOWS Press the defroster control button to turn the system on The A C automatically turns on when the defroster mode is selected.
Download
To cancel cruise control push the CANCEL switch or tap the brake pedal The SET indicator light in the instrument panel will go out To turn off cruise control push the ON OFF switch Both the CRUISE indicator light and the SET indicator light in the instrument panel will go out Use the dials 03 at the side of the driver s seat to adjust the angle and height of the seat cushion With power seats if so equipped Move the control 04 forward or backward to adjust the seat cushion forward or backward Pull up to raise the driver s seat cushion press down to lower the cushion 04 Push the switch 05 forward to move the seatback forward press it back to move the seatback backward Your driver s seat has a lumbar support adjust it by moving the lever 06 forward or backward 12 02 04 05 01 14 AUTOMATIc clIMATE cONTROl if so equipped 01 Press the REAR CTRL button to transfer rear climate functions to the rear passengers 05 06 04 06 03 AUTO BUTTON Press the AUTO button 01 Turn the driver s side temperature control dial 02 to the desired temperature This will allow the fan speed air flow distribution and temperature to be automatically maintained Press the DUAL 03 button to turn the passenger s side temperature controls on or off This will allow the passenger s side temperature to be adjusted independently from driver s side control When AUTO is pressed AUTO will be displayed When DUAL is pressed DUAL will be displayed DRIVER S SIDE TEMPERATURE CONTROL DIAL Turn the driver s temperature control dial left for cold air or right for hot air PASSENGER S SIDE TEMPERATURE CONTROL DIAL Turn the passenger s temperature control dial left for cold air or right for hot air AIR FLOW MODE BUTTONS Press to select the following air flow outlets Air flows from the center and side vents Air flows from the center side and foot vents Air flows mainly from the foot vents Air flows from the defroster and foot vents Air flows mainly from the defroster vents FAN SPEED CONTROL BUTTONS Press slower or faster button repeatedly to manually control fan speed Press AUTO to automatically control fan speed Press OFF to cancel fan speed operation DEFROSTING DEFOGGING FRONT AND SIDE WINDOWS Press the defroster control button to turn the system on The A C automatically turns on when the defroster mode is selected.
Download
Saturday, May 1, 2010
2006 Nissan Quest Owners Manual
Slip indicator light and Vehicle dynamic control VDC off indicator light in the Instruments and controls section Indicator light If malfunction occurs in the system and indicator lights come the on in the instrument panel As long as these indicator lights are on the traction control function is canceled. The Slip indicator will flash if wheel spin is detected The ABS will still operate with the VDC system off.
When the VDC system is operating you may feel a pulsation in the brake pedal and hear a noise or vibration from under the hood This is normal and indicates that the VDC system is working properly The computer has a built in diagnostic feature that tests the system each time you start the engine and move the vehicle forward or in reverse at a slow speed When the self test occurs you may hear a clunk noise and or feel a pulsation in the brake pedal This is normal and is not an indication of a malfunction WARNING The vehicle dynamic control system is designed to help improve driving stability but does not prevent accidents due to abrupt steering operation at high speeds or by careless or dangerous driving techniques Reduce vehicle speed and be especially careful when driving and cornering on slippery surfaces and always drive carefully Starting and driving 5 21 REVIEW COPY 2006 Quest van Owners Manual USA English nna 05 27 05 tbrooks REAR SONAR SYSTEM if so equipped If brake related parts such as brake pads rotors and calipers are not standard equipment or are extremely deteriorated the vehicle dynamic control system may not operate properly and the vehicle dynamic control off indicator light may come on Do not modify the vehicle s suspension If suspension parts such as shock absorbers struts springs stabilizer bars and bushings are not NISSAN approved for your vehicle or are extremely deteriorated the vehicle dynamic control system may not operate properly This could adversely affect vehicle handling performance and the VDC OFF indicator light may come on When driving on extremely inclined surfaces such as higher banked corners the vehicle dynamic control system may not operate properly and the VDC OFF indicator light may come on Do not drive on these types of roads When driving on an unstable surface such as a turntable ferry elevator or ramp the vehicle dynamic control off indicator light may illuminate
Download
When the VDC system is operating you may feel a pulsation in the brake pedal and hear a noise or vibration from under the hood This is normal and indicates that the VDC system is working properly The computer has a built in diagnostic feature that tests the system each time you start the engine and move the vehicle forward or in reverse at a slow speed When the self test occurs you may hear a clunk noise and or feel a pulsation in the brake pedal This is normal and is not an indication of a malfunction WARNING The vehicle dynamic control system is designed to help improve driving stability but does not prevent accidents due to abrupt steering operation at high speeds or by careless or dangerous driving techniques Reduce vehicle speed and be especially careful when driving and cornering on slippery surfaces and always drive carefully Starting and driving 5 21 REVIEW COPY 2006 Quest van Owners Manual USA English nna 05 27 05 tbrooks REAR SONAR SYSTEM if so equipped If brake related parts such as brake pads rotors and calipers are not standard equipment or are extremely deteriorated the vehicle dynamic control system may not operate properly and the vehicle dynamic control off indicator light may come on Do not modify the vehicle s suspension If suspension parts such as shock absorbers struts springs stabilizer bars and bushings are not NISSAN approved for your vehicle or are extremely deteriorated the vehicle dynamic control system may not operate properly This could adversely affect vehicle handling performance and the VDC OFF indicator light may come on When driving on extremely inclined surfaces such as higher banked corners the vehicle dynamic control system may not operate properly and the VDC OFF indicator light may come on Do not drive on these types of roads When driving on an unstable surface such as a turntable ferry elevator or ramp the vehicle dynamic control off indicator light may illuminate
Download
Friday, April 30, 2010
2004 Nissan Quest Navigation System Manual
The brightness adjustment is at the lowest setting No map DVD ROM is inserted or it is inserted upside down The map display mode is switched off Remedy Adjust the settings to make the display brighter Insert the DVD ROM correctly Press the MAP button No voice guide is available or The volume is not high enough The screen is too dim The movement is slow There are a few darker or brighter dots in the display The volume is not set correctly or turned off Adjust the volume correctly The temperature in the vehicle is low This is inherent to displays This condition is a characteristic of liquid crystal displays Wait for the temperature in the vehicle to rise
This condition is not abnormal Stored location in the address book and other memory functions may be lost if the vehicle s battery is disconnected or becomes discharged for a long time If this should occur service the vehicle s battery as necessary and re enter the address book information Troubleshooting guide 13 3 REVIEW COPY 2004 Quest van Navigation System OM navi USA English nna 05 05 04 debbie VEHICLE ICON Symptom The location names differ between Planview and Birdview Possible cause This is because the displayed information is reduced so that the screen does not become too crowded There is also a chance that names of roads or locations will be displayed twice.
Download
This condition is not abnormal Stored location in the address book and other memory functions may be lost if the vehicle s battery is disconnected or becomes discharged for a long time If this should occur service the vehicle s battery as necessary and re enter the address book information Troubleshooting guide 13 3 REVIEW COPY 2004 Quest van Navigation System OM navi USA English nna 05 05 04 debbie VEHICLE ICON Symptom The location names differ between Planview and Birdview Possible cause This is because the displayed information is reduced so that the screen does not become too crowded There is also a chance that names of roads or locations will be displayed twice.
Download
Subscribe to:
Posts (Atom)