Finally, the intake manifold boasts shorter runners and a single nonstaged two-barrel throttle body for lower hoodline and higher peak rpm horsepower. See how you can personalize your Viper with Performance Parts from Mopar to get 500 horsepower, 525 lb-ft of torque, and 505 cubic inches of displacement, the Viper’s powerful V10 engine has a large bore cast-aluminum block and a long-stroke crankshaft.
Download
Showing posts with label intake. Show all posts
Showing posts with label intake. Show all posts
Saturday, May 8, 2010
Wednesday, May 5, 2010
Acura B18 Valve Spring Set Instructions
The COMP Cams® Acura/Honda B-Series VTEC valve spring set (Fig. A) utilizes dual springs on the intake side and a single spring on the exhaust side. Below are the information and diagrams to ensure correct installation.
Installation Instructions:
Dual Intake Spring
Installed Height: 60lbs at 1.375
Open Height: 220 lbs at .875
Coil Bind Height: .815
Spring Rate: 300 lbs per inch
Single Exhaust Spring
Installed Height: 43 lbs at 1.375
Open Height: 148 lbs at .875
Coil Bind Height: .815
Spring Rate: 210 lbs per inch
Warnings and maintenance information! It is important to orientate the outer valve spring of the intake and exhaust (See Fig. B & C) with the *tightly wound coils on the bottom. THE ORIENTATION OF THE INNER INTAKE SPRING IS NOT CRITICAL.
*Note: To figure out which end is the tightly wound end start at the end of the coil. Follow it around 180° (See Fig. D) then look at the distance between the two coils. Now follow the same steps from the other end of the spring. Whichever end is closest together needs to be on the bottom.
Download
Installation Instructions:
Dual Intake Spring
Installed Height: 60lbs at 1.375
Open Height: 220 lbs at .875
Coil Bind Height: .815
Spring Rate: 300 lbs per inch
Single Exhaust Spring
Installed Height: 43 lbs at 1.375
Open Height: 148 lbs at .875
Coil Bind Height: .815
Spring Rate: 210 lbs per inch
Warnings and maintenance information! It is important to orientate the outer valve spring of the intake and exhaust (See Fig. B & C) with the *tightly wound coils on the bottom. THE ORIENTATION OF THE INNER INTAKE SPRING IS NOT CRITICAL.
*Note: To figure out which end is the tightly wound end start at the end of the coil. Follow it around 180° (See Fig. D) then look at the distance between the two coils. Now follow the same steps from the other end of the spring. Whichever end is closest together needs to be on the bottom.
Download
2000-05 Volkswagen Jetta/Golf 1.8 K&N Drycharger Installation
The K&Nо Drycharger included with this kit must be installed on the K&Nо air filter when used with this K&Nо cold air intake system. The K&N cold air intake system a performance product that can be used safely during mild weather conditions. During harsh and inclement weather conditions, you must convert your cold air intake system to a short ram configuration, or return your vehicle to the stock OEM air box and intake tract configuration. Failure to follow these instructions can void your warranty.
Installation:
1. Turn off the ignition and disconnect the negative battery cable.
NOTE: Disconnecting the negative battery cable erases pre-programmed electronic memories. Write down all memory settings before disconnecting the negative battery cable. Some radios will require an anti-theft coded to be entered after the battery is reconnected. The anti-theft code is typically supplied with your owner’s manual. In the event your vehicles’ anti-theft code cannot be recovered, contact an authorized dealership to obtain your vehicles anti-theft code.
2. Depress the tabs on the side of the battery cover and remove as shown.
3. First disconnect the negative battery cable, then disconnect the positive battery cable as shown.
4. Disconnect the mass air sensor electrical connection as shown.
5. Loosen the hose clamp at the mass air sensor as shown.
6. Remove the air cleaner cover screws as shown.
7. Disconnect the air pump vent hose as shown.
8. Remove the air cleaner cover as shown.
Download
Installation:
1. Turn off the ignition and disconnect the negative battery cable.
NOTE: Disconnecting the negative battery cable erases pre-programmed electronic memories. Write down all memory settings before disconnecting the negative battery cable. Some radios will require an anti-theft coded to be entered after the battery is reconnected. The anti-theft code is typically supplied with your owner’s manual. In the event your vehicles’ anti-theft code cannot be recovered, contact an authorized dealership to obtain your vehicles anti-theft code.
2. Depress the tabs on the side of the battery cover and remove as shown.
3. First disconnect the negative battery cable, then disconnect the positive battery cable as shown.
4. Disconnect the mass air sensor electrical connection as shown.
5. Loosen the hose clamp at the mass air sensor as shown.
6. Remove the air cleaner cover screws as shown.
7. Disconnect the air pump vent hose as shown.
8. Remove the air cleaner cover as shown.
Download
Monday, July 21, 2008
How Camshafts Work
In this article, you will learn how the camshaft affects engine performance. We've got some great animations that show you how different engine layouts, like single overhead cam (SOHC) and double overhead cam (DOHC), really work. And then we'll go over a few of the neat ways that some cars adjust the camshaft so that it can handle different engine speeds more efficiently.
The key parts of any camshaft are the lobes. As the camshaft spins, the lobes open and close the intake and exhaust valves in time with the motion of the piston. It turns out that there is a direct relationship between the shape of the cam lobes and the way the engine performs in different speed ranges.
To understand why this is the case, imagine that we are running an engine extremely slowly -- at just 10 or 20 revolutions per minute (RPM) -- so that it takes the piston a couple of seconds to complete a cycle. It would be impossible to actually run a normal engine this slowly, but let's imagine that we could. At this slow speed, we would want cam lobes shaped so that:
Just as the piston starts moving downward in the intake stroke (called top dead center, or TDC), the intake valve would open. The intake valve would close right as the piston bottoms out.
The exhaust valve would open right as the piston bottoms out (called bottom dead center, or BDC) at the end of the combustion stroke, and would close as the piston completes the exhaust stroke.
This setup would work really well for the engine as long as it ran at this very slow speed. But what happens if you increase the RPM? Let's find out. When you increase the RPM, the 10 to 20 RPM configuration for the camshaft does not work well. If the engine is running at 4,000 RPM, the valves are opening and closing 2,000 times every minute, or 33 times every second. At these speeds, the piston is moving very quickly, so the air/fuel mixture rushing into the cylinder is moving very quickly as well.
Download
The key parts of any camshaft are the lobes. As the camshaft spins, the lobes open and close the intake and exhaust valves in time with the motion of the piston. It turns out that there is a direct relationship between the shape of the cam lobes and the way the engine performs in different speed ranges.
To understand why this is the case, imagine that we are running an engine extremely slowly -- at just 10 or 20 revolutions per minute (RPM) -- so that it takes the piston a couple of seconds to complete a cycle. It would be impossible to actually run a normal engine this slowly, but let's imagine that we could. At this slow speed, we would want cam lobes shaped so that:
Just as the piston starts moving downward in the intake stroke (called top dead center, or TDC), the intake valve would open. The intake valve would close right as the piston bottoms out.
The exhaust valve would open right as the piston bottoms out (called bottom dead center, or BDC) at the end of the combustion stroke, and would close as the piston completes the exhaust stroke.
This setup would work really well for the engine as long as it ran at this very slow speed. But what happens if you increase the RPM? Let's find out. When you increase the RPM, the 10 to 20 RPM configuration for the camshaft does not work well. If the engine is running at 4,000 RPM, the valves are opening and closing 2,000 times every minute, or 33 times every second. At these speeds, the piston is moving very quickly, so the air/fuel mixture rushing into the cylinder is moving very quickly as well.
Download
Subscribe to:
Posts (Atom)